I have tested this D-Link DWL-G122. Did it again. It only works a while. After restarting the receiver there's no way to make it work again.
Fixed connection through electric power network is the only working solution for me so far.
I have tested this D-Link DWL-G122. Did it again. It only works a while. After restarting the receiver there's no way to make it work again.
Fixed connection through electric power network is the only working solution for me so far.
Vu+Ultimo/D80cm motorized/OpenVix5.2.045ViXBMC1080Confluence/1xDVB-S2+1xDVB-C/T+1xDVB-C/T/T2 &
Vu+Ultimo4K/D80cm 2LNB/OpenVix6.6.007ViXBMC1080Confluence/1xDVB-S2+1xDVB-C/T+1xDVB-C/T/T2
is there any way to update the firmware on the netgear WNDA3200 stick ?
Someone says earlier it doesnt work.
VU+DUO (Genuine box - not a clone)
FIXED 28.2e DISH
System OE:OE-Alliance 3.4
Firmware version:OpenViX 4.2.021 (2016-12-06)
Kernel / Drivers:3.9.6 / 20151124
hi iam i right in thinking you need a router has well as dongle ?? or will dongle work by its self
you need a wireless router for the wireless usb stick to log onto inorder to have access to the internet
"Patience is a virtue, Possess it if you can"
-------------------------------------------------------------------------------------------------------------------------------------------------------
How to Install Cams on ViX Image - Click Here / How to Setup Picons on ViX Image - Click Here
How to Use Image Manager & Backup Manager on ViX Image - Click Here / How to Use Log Manager on ViX Image - Click Here
How to Setup Inadyn on ViX Image - Click Here / How To Update Satellites.xml File - Click Here
How To Stream TV To iPhone & iPad - Click Here
-------------------------------------------------------------------------------------------------------------------------------------------------------
D I S C L A I M E R
My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!
PM HELP WILL BE IGNORED PLEASE POST HERE IN FORUM AS IT BENEFITS EVERYONE
how i can know the version of TP-Link TL-WN321G?
Last edited by kevdoc; 01-08-11 at 00:54.
a driver package for this dongle doesnt exist, yet. I have managed to get hold of the actual source code that drivers get compiled from for this dongle though, as well as pre compiled .fw firmware files, but am struggling to compile the required .ko files that are needed for the receiver to work
i have more than everything needed to create the driver package, i just dont have the knowledge or experience to do it, so if anyone wants to point me in the right direction, ill see what i can come up with
Working fine for me mate. TP-Link TL-WN321G (version 4) WHITE
I'd you have any kind of encryption on your router you will need to first use the dongle to connect to the router via a desktop or a laptop so it has the correct settings before connecting via vu+. Not so sure like but I think there's no way to configure these settings via the box. So it should be down first and a profile should be saved for said router your trying to connect to. Hope this helps you in some way.
kevdoc (01-08-11)
do you have any information about TP-Link TL-WN321G version 3.4 that it work or no?
I don't know then mate, def working for me. Have you updated the software on it? You can get the latest from that like I posted above, worth giving that a go an see how that goes. Also what version of vix are you running ATM? I'm running 2.2.100. Might be a driver issue or something.
nibb (03-08-11)
There is no 3.4 mate. At least hardware revisions anyway. Check the link I posted above and find your correct hardware revision. Hardware revisions run from V1,V2, V3 and V4. I'm sure the problems nibb is having is software based rather than hardware as I can guarantee 100% V4 is working on vu+ Duo.
Finally I've found it: TP-Link TL-WN321G Ver3.3 works now fine with Vu+Duo!
Vu+Ultimo/D80cm motorized/OpenVix5.2.045ViXBMC1080Confluence/1xDVB-S2+1xDVB-C/T+1xDVB-C/T/T2 &
Vu+Ultimo4K/D80cm 2LNB/OpenVix6.6.007ViXBMC1080Confluence/1xDVB-S2+1xDVB-C/T+1xDVB-C/T/T2