Hi,
To install last PLi 2.1 image i load the boatloader 2.6.31 in myxtrend receiver. If i want flash again and install the vix 2.2.100 image i could do or i have install the kernel 2.6.18?
Best regards
Hi,
To install last PLi 2.1 image i load the boatloader 2.6.31 in myxtrend receiver. If i want flash again and install the vix 2.2.100 image i could do or i have install the kernel 2.6.18?
Best regards
Just flash with ViX, bootloader loader is backwards compatible.
D I S C L A I M E R
My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!
Please help keep OpenViX online, donate HERE.
Rules can be found HERE
Support our sponsor World-Of-Satellite HERE
GIGABLUE UHD QUAD 4K, VU+ DUO 4K SE, ZGEMMA H7S, VU+ UNO 4K SE
Triax 1.1m Powered by TM2600, Fixed 28.2 Zone 2 dish with GT-SAT Unicable
Hi,
Many thanks. A few minutes when i tried flash, the vix image was note installed. With the bootloader 2.6.31 instaled, the vix folder must have the name et5000 or et5x00?
Regards
et5000 mate
"Patience is a virtue, Possess it if you can"
-------------------------------------------------------------------------------------------------------------------------------------------------------
How to Install Cams on ViX Image - Click Here / How to Setup Picons on ViX Image - Click Here
How to Use Image Manager & Backup Manager on ViX Image - Click Here / How to Use Log Manager on ViX Image - Click Here
How to Setup Inadyn on ViX Image - Click Here / How To Update Satellites.xml File - Click Here
How To Stream TV To iPhone & iPad - Click Here
-------------------------------------------------------------------------------------------------------------------------------------------------------
D I S C L A I M E R
My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!
PM HELP WILL BE IGNORED PLEASE POST HERE IN FORUM AS IT BENEFITS EVERYONE
ET5000 and you need to press up on the front radial buttons after powering off and than on.
Flashing instructions here http://www.world-of-satellite.com/sh...B-memory-stick
Support The Sponsor - Buy from the best HERE
Please abide by the rules - have a read HERE
VIX manual & guides >>HERE
Download images from >> HERE
New Box Setup Guide >>HERE
D I S C L A I M E R
My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!
PM HELP WILL BE IGNORED PLEASE POST HERE IN FORUM AS IT BENEFITS EVERYONE
Follow us on Twitter
NO CARD SHARING TALK WILL BE TOLERATED, LAN OR WAN! IN OPEN FORUM OR PM
IF THE POSTS HELP PLEASE CLICK THANKS OR ADD TO REP ?
@ sicillian,
I load the new boatloader 2.6.31 in my xtrend et5000 receiver, now i have only the first page witch " BOOTLOADER LINUX 2.6.31.UBIFS BOOTING ....."
Wat I can do ? I can't flashing a new image animore.
Thx,
MAJOOR
D I S C L A I M E R
My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!
Please help keep OpenViX online, donate HERE.
Rules can be found HERE
Support our sponsor World-Of-Satellite HERE
GIGABLUE UHD QUAD 4K, VU+ DUO 4K SE, ZGEMMA H7S, VU+ UNO 4K SE
Triax 1.1m Powered by TM2600, Fixed 28.2 Zone 2 dish with GT-SAT Unicable
I have put the last pli 2.1 in folder et5000 on pendriver
I put the pendriver in the front usb and then press up on the front radial buttons after powering off and than on .
the pendriver blinkect few time and then stop. The same screen witch " BOOTLOADER LINUX 2.6.31.UBIFS BOOTING ....."
MAJOOR
Hi,
At this moment i have this problem. I restarted the receiver and always appear the message " BOOTLOADER LINUX 2.6.31.UBIFS BOOTING .....". After some minutes the screen is green. I tried everything, flashing the receiver with several images, but i can´t solve this problem.
This happened after disconnecting all cables from the receiver to change the location of receiver in my room. After that always BOOTLOADER LINUX 2.6.31.UBIFS BOOTING ....."
Anyone could help me, please!!!!!!
Best regards
this happened to one of our mods a few days ago and what i advised him worked so you could try it
get the latest bootloder and place it into file et5x00 [not et5000]
insert USB stick and press the oposite button to initiate flash
so i think that up arrow ley
the bootloder will reflash onto box [normally pressing down wont flash it]
once done get latest public ViX image and flash that
but this time go the normal flashing route of pressing down arrow
things should be sorted
if i got up and down wrong then sorry but its one or the other
PM HELP WILL BE IGNORED PLEASE POST HERE IN FORUM AS IT BENEFITS EVERYONE
NO CARD SHARING TALK WILL BE TOLERATED, LAN OR WAN! IN OPEN FORUM OR PM
IF THE POSTS HELP PLEASE CLICK THANKS OR ADD TO REP ↓
yes just had a check
Normal flash method is to press UP ARROW
you need to press DOWN ARROW to flash bootloder and then
when flashing image do it normal way by pressing UP ARROW
PM HELP WILL BE IGNORED PLEASE POST HERE IN FORUM AS IT BENEFITS EVERYONE
NO CARD SHARING TALK WILL BE TOLERATED, LAN OR WAN! IN OPEN FORUM OR PM
IF THE POSTS HELP PLEASE CLICK THANKS OR ADD TO REP ↓
I follow your recomendations but the problem. However something was writed in flash, because now don´t appear the xtrend symbol with message "booting 2.6.31. Now appears " OPENVIX VIRTUOSO IMAGE XTREME www.xtrend-support.co.uk. Minutes after again the green screen and always the lights green and red in the receiver display.
I installed the bootloder 3.1.0 and vix 2.3.133.
Any sugestion now?
Best regards
PM HELP WILL BE IGNORED PLEASE POST HERE IN FORUM AS IT BENEFITS EVERYONE
NO CARD SHARING TALK WILL BE TOLERATED, LAN OR WAN! IN OPEN FORUM OR PM
IF THE POSTS HELP PLEASE CLICK THANKS OR ADD TO REP ↓