I have looked on dish-pointer and the lon and lat he quotes in an earlier post put is dish on the back of a silver car, i bet it drove away and thats why he lost the picture.
I have looked on dish-pointer and the lon and lat he quotes in an earlier post put is dish on the back of a silver car, i bet it drove away and thats why he lost the picture.
So that's what they were gettings at when they said 'motor moves faster than previous model'
LOOOOL ill get the correct settings when i get home.
Thanks guys....
When your dish moves and you get the dish icon on the screen does it just keep flashing as if its moving and you get nothing on the screen, if that happens your dish as already moved but isn't locking onto a signal,just tried it myself on 42e and thought the dish hadn't moved till i had a look ,went onto a channel i could receive, the channel came on icon went off.
If this is whats happening to you it looks like the dish isn't set up properly , just a thought you never know.
[QUOTE=bob1;7177]When your dish moves and you get the dish icon on the screen does it just keep flashing as if its moving and you get nothing on the screen[QUOTE]
Yes this does happen...it eventually stops flashing and shows nothing. Sometimes the dish doesnt even move.
Are you sure it doesn't move , can you see it from where your box is, some satellites are close together ,blink and you might miss it.
Just checked and the lon and lat is correct:
Latitude: 51.7612°
Longitude: -0.2298°
Would i round up the Longitude?
Yep you only get the option of the 3 digits after the . on Enigma2 firmware so just round up (or down in some cases) as it won't make any real difference.
Guys I have imaged the box, set the lon and lat, plugged in only one cable from lnb and added enigma 2 files. I selected thor sat and the dish moved. But no channels show. Moved it to turksat, dish moved again but the flashing dish is still on screen but dish has actually stopped moving.
Once the dish icon stopped flashing I selected another channel on turksat and the flashing sat has come up again....but the dish isn't moving.
That means you are at Turksat already by the sounds of it but you won't pick up all channels from Turksat, they have different beams, so to me it sounds like it's working, try going to a channel on Astra 19E for example or Hotbird 13E, or even Astra 2 (SKY UK), then back to Thor again, choose some FTA channels to test, pay ones of course you won't get anything other than a black screen!! BBC News on Thor is a good one that's FTA to test out....
sn196 (09-07-10)
I can confirm that the TM 2600 works great with the duo. I had a problem though when it was installed using a Starview HD combo receiver. The F plugs weren't screwed in very well and the one from the receiver was only held in place by the rubber weather shroud, so it looked like it was connected properly but it wasn't. This gave somewhat erratic behavior for an hour or so untill it stopped working all together as it worked looser. I didn't know this at the time and I spent hours trying to configure it. I found the Fplug had worked loose as a last resort after getting the ladders out, just a thought.
It also might be worth resetting the motors sat table as with all the messing about I did, it went all to cock. There is a pin hole to probe which I think has a rubber cap over it.
One other thing is my motor has moved around the pole a few degrees since it was installed (I've got to readjust it) so I have to enter in every now & then new longitude settings to compensate for the error. My true longitude is 2 deg west but I'm now set at 1deg East.
Maybe of some use, worth a look I guess.
sn196 (09-07-10)
sn196 (09-07-10)
Anyone mind if I scream????????
ARRRRRRRGGGGGGGGHHHHHHHHHHHH!!!!!!!!!
Just reimaged the box again....didn't change any settings, just chose simple settings without inserting my lon lat details, just chose default.
Selected default service lists........guess what.........IT WORKS!!!!!!!!!
Ftpd the enigma 2 files and I can now watch most fta channels!!!!!
Only thing is that the signal strength is aroud 60% so not pickinjg up all fta channels.
Anyone know how I cud make the signal better??? Would it be a case of moving the dish manually???