We have looked into that, but we couldn't reproduce this.
Suggestion is that your settings are not OK, as the box can't find a channel.
We have looked into that, but we couldn't reproduce this.
Suggestion is that your settings are not OK, as the box can't find a channel.
Help asked via PM will be ignored.
The forum is there for help and all will benefit from your questions.
NO CARD SHARING TALK WILL BE TOLERATED, LAN OR WAN, IN OPEN FORUM OR PM !
English is not my native tongue.
I apologise for all my grammar, spelling and idiom errors.
So why does it only do it from deep standby then? If i hard reset the box it's fine. Untill the next time after deep standby. After flashing i install perm timeshift, add cline, add cccam 2.1.4 and send over rats channel list add picons and setup cross epg. Thats it. The only thing im doing different to previous iq images is adding perm timeshift as that plug in did not work.
Last edited by Rob van der Does; 19-10-12 at 21:04.
Help asked via PM will be ignored.
The forum is there for help and all will benefit from your questions.
NO CARD SHARING TALK WILL BE TOLERATED, LAN OR WAN, IN OPEN FORUM OR PM !
English is not my native tongue.
I apologise for all my grammar, spelling and idiom errors.
Sargie, this issue is being investigated, can you please PM me your serial number.
D I S C L A I M E R
My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!
Please help keep OpenViX online, donate HERE.
Rules can be found HERE
Support our sponsor World-Of-Satellite HERE
GIGABLUE UHD QUAD 4K, VU+ DUO 4K SE, ZGEMMA H7S, VU+ UNO 4K SE
Triax 1.1m Powered by TM2600, Fixed 28.2 Zone 2 dish with GT-SAT Unicable
sargie (20-10-12)
D I S C L A I M E R
My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!
Please help keep OpenViX online, donate HERE.
Rules can be found HERE
Support our sponsor World-Of-Satellite HERE
GIGABLUE UHD QUAD 4K, VU+ DUO 4K SE, ZGEMMA H7S, VU+ UNO 4K SE
Triax 1.1m Powered by TM2600, Fixed 28.2 Zone 2 dish with GT-SAT Unicable
hiya, ive been helping a friend with his tm twin and it isnt running very well, last time i was there i enable logs in the logs mananger settings and have been to his again to transfer them onto a usb and send to the right people, he gets alot of lock ups, vix image in top left corner and box wont respond unless he turns it off and on from the back, he also gets alot of random reboots, can be watching tv and the box will just reboot its self, who shall i send this log files to ? thanks
Easiest way is to send logs to us directly from the box (using logmanager).
You can also post them here.
Help asked via PM will be ignored.
The forum is there for help and all will benefit from your questions.
NO CARD SHARING TALK WILL BE TOLERATED, LAN OR WAN, IN OPEN FORUM OR PM !
English is not my native tongue.
I apologise for all my grammar, spelling and idiom errors.
New folder.rar
hiya, il try enabling that auto send then when im round at my friends house next time, for now il just upload what i have to here, thanks
Memory problems and segfault.
I would advise to flash the box, do not use a settings restore, make your settings and activate a swapfile.
Also make sure EPG-import is properly set up.
Help asked via PM will be ignored.
The forum is there for help and all will benefit from your questions.
NO CARD SHARING TALK WILL BE TOLERATED, LAN OR WAN, IN OPEN FORUM OR PM !
English is not my native tongue.
I apologise for all my grammar, spelling and idiom errors.
dilly1066 (26-10-12)
hiya, i never restore settings, always use new ones, been using catseye channel list as thats the one he likes is that ok ? i been using the xgeped (i no thats spelt wrong lol) epg settings, where it stays on the same channel and downloads the egp in a minute or 2, it has a usb stick in the back for epg so could create a swap file on there, also its been flashed lots of times, are them settings and list ok to use ? only thing im not 100% sure on is whether i made a swapfile or not, apart from that the above is all i do, thanks
So no answer to my problem yet then? What was the result of pming my serial number? I have reflashed yet again and the problem still persists i guess this is now a problem for tm and not vix?
sargie, what build are you currently using?
what bouquets are you currently using?
I know it doesn't help & I've been harsh on this box in the past, but it's working perfect for me lately.
hiya, managed to get to my friends house yesterday and flashed the latest image onto his box, set up everything from scratch like normal, made a swap file this time on the usb stick, also tried a different channel list , usually use catseye but tried misters channel list, went round again today and its still the same for him, freezing and glitching on free to air channels, box randomly rebooting, heres log files i took from his box earlier
vix build 390 logs.rar
im not sure what else to do, thanks
I suggest to flash twice as follows: -
- Use latest build 393 http://www.world-of-satellite.com/en...ir=TM-Twin-OE/
- Format USB stick fat32.
- Copy update folder to root of USB stick.
- Download bootloader from here http://www.world-of-satellite.com/en...rs/TM-TWIN-OE/
- Copy the cfe.bin to your USB stick and place with the flash files. update > tmtwin > cfe, copy into directory.
- Flash the image, press ok when prompted on TV.
- When complete power off, wait 30 seconds, power on and flashed again.
- Once second flash is complete, power off for 30 seconds.
- Power on and repeatedly press EXIT on top of front panel until openvix splash screen disappears.
- Setup completely fresh, do not restore anything.
If you getting freezing and glitching on FTA then I'd seriously look and your feed.
D I S C L A I M E R
My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!
Please help keep OpenViX online, donate HERE.
Rules can be found HERE
Support our sponsor World-Of-Satellite HERE
GIGABLUE UHD QUAD 4K, VU+ DUO 4K SE, ZGEMMA H7S, VU+ UNO 4K SE
Triax 1.1m Powered by TM2600, Fixed 28.2 Zone 2 dish with GT-SAT Unicable
abu baniaz (31-10-12)