ok im getting there, Ive now made the lights work (there is a but at the end)
Installed following and rebooted: opkg install kernel-module-cdc-acm kernel-module-ftdi-sio
I then installed boblight plugin and made the enigmalight.conf, then tried to run it manually via cmd line, got loads of errors.
Code:
root@vuduo2:/etc# boblightd
Boblight Daemon - for enigma2 0.8r6 (c) 2012-2013 Speedy1985 and Oktay Oeztueter)
(InitLog) start of log /home/root/.boblight/boblightd.log
(PrintFlags) starting boblightd
(CConfig::LoadConfigFromFile) opening /etc/boblight.conf
(CConfig::CheckConfig) checking config lines
(CConfig::CheckLightConfig) ERROR: /etc/boblight.conf line 43 section [light]: name (2) must be 3 chars
(CConfig::CheckLightConfig) ERROR: /etc/boblight.conf line 51 section [light]: name (3) must be 3 chars
(CConfig::CheckLightConfig) ERROR: /etc/boblight.conf line 61 section [light]: name (top1) must be 3 chars
(CConfig::CheckLightConfig) ERROR: /etc/boblight.conf line 69 section [light]: name (top2) must be 3 chars
(CConfig::CheckLightConfig) ERROR: /etc/boblight.conf line 77 section [light]: name (top3) must be 3 chars
(CConfig::CheckLightConfig) ERROR: /etc/boblight.conf line 87 section [light]: name (left1) must be 3 chars
(CConfig::CheckLightConfig) ERROR: /etc/boblight.conf line 95 section [light]: name (left2) must be 3 chars
(CConfig::CheckLightConfig) ERROR: /etc/boblight.conf line 105 section [light]: name (end1) must be 3 chars
(CConfig::CheckLightConfig) ERROR: /etc/boblight.conf line 113 section [light]: name (end2) must be 3 chars
Renamed lights to be 3 Characters
Code:
root@vuduo2:/etc# boblightd
Boblight Daemon - for enigma2 0.8r6 (c) 2012-2013 Speedy1985 and Oktay Oeztueter)
(InitLog) start of log /home/root/.boblight/boblightd.log
(PrintFlags) starting boblightd
(CConfig::LoadConfigFromFile) opening /etc/boblight.conf
(CConfig::CheckConfig) checking config lines
(CConfig::CheckConfig) config lines valid
(CConfig::BuildConfig) building config
(CConfig::BuildConfig) built config successfully
(main) Starting devices
(CClientsHandler::Process) opening listening socket on *:19333
(CDevice::Process) AmbiLight: starting
(CDevice::Process) AmbiLight: setting up
(CDeviceLightpack::SetupDevice) AmbiLight: found Lightpack at bus 5 address 7, serial is 8543636313035131C070
(CDeviceLightpack::SetupDevice) AmbiLight: Lightpack is initialized, bus 5 device address 7
(CDevice::Process) AmbiLight: setup succeeded
(CClientsHandler::Process) 127.0.0.1:41603 connected
(CClientsHandler::ParseMessage) 127.0.0.1:41603 said hello
(CClientsHandler::ParseSet) 127.0.0.1:41603 priority set to 128
(CClientsHandler::Process) 127.0.0.1:41603 Connection closed
Wen't into the plugin and woohoo lights work! (hit yellow for restart, then green to turn lights on) but they were not synced correctly.
I then had to modify the H and V scans because the ones on that config file on the kodi forum link were just not right causing the sync issue. Once done, everything was perfect.
I then rebooted......and the box freezes again after the smart linux tv icon, just sits with "double you expectation" on the screen.
arrrrrrrg, really hope someone can help me figure out what is causing this freeze, getting so close!
.