Sorry mate but dont wanna rub salt in the wound but my cam is working & i have a footy match to watch but there are loads of others that will jump in to give you a hand if you keep posting. Good luck.
Sorry mate but dont wanna rub salt in the wound but my cam is working & i have a footy match to watch but there are loads of others that will jump in to give you a hand if you keep posting. Good luck.
Blu-ray (14-02-11)
Anybody know where the CCcam confg goes, got 2 answers back, ect or usr/softcam.
it goes in /etc
Support The Sponsor - Buy from the best HERE
Please abide by the rules - have a read HERE
VIX manual & guides >>HERE
Download images from >> HERE
New Box Setup Guide >>HERE
D I S C L A I M E R
My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!
PM HELP WILL BE IGNORED PLEASE POST HERE IN FORUM AS IT BENEFITS EVERYONE
Follow us on Twitter
NO CARD SHARING TALK WILL BE TOLERATED, LAN OR WAN! IN OPEN FORUM OR PM
IF THE POSTS HELP PLEASE CLICK THANKS OR ADD TO REP ?
Blu-ray (14-02-11)
Blu-ray (15-02-11)
Hi mate
Instead of mucking about with ipk why dont you ftp the files direct into the receiver
in user >> softcam install the CCcam bin file like CCcam.2.2.1
in var >> etc install the CCcam.cfg >> prio >> channel >>>provider files
Dont forget to chmod them
regards
satmanbasil
Blu-ray (15-02-11)
What are the chmod for CCcam 2.2.1 and CCcam.cfg.
I'm not sure if this is what you mean but "755"
-----------------------------------------------------------------------------------------------
VU+ Zero - Triax TD110 - Inverto Black Ultra twin LNB - Superior DarkMotor - VIX v3.2
Blu-ray (15-02-11)
2 days and still no closer to getting vix 2.0 working, i am told CCcam 2.1.1 chmod 755 goes in TMP, CCcam.cfg goes in ECT chmod 755,what goes in the USR/SOFTCAM !,i put CCcam 2.1.1 inTMP last night now this morning it has gone, also do you delete the mispel & ipk of the CCcam and just enter 2.1.1.
Hi mate
When you go to Menu > Setup > Softcam > Softcam Manager
Is anything showing in there?
In softcam manager there is selected = CCcam.cfg, active =, autostart =CCcam.cfg.also got CCcam.cfg ect.
That is all setup wrong then. You seem to have the wrong files.
I would suggest you ftp to the box & delete anything you can find that is to do with CCcam and start all over again with another .ipk file.
Done that, where have i gone wrong.
LoL i dunno mate
Check your private message so i can sort out sending you the file
If you load an "ipk" file via an ftp programe, ie; filezilla, flashfxp, you simply transferr the file to the folder called "TMP" there should be no need to ch mod the file, but 755 = exicutable
once in temp, you can then install it via your manual addons
the config file should be ftp,d to ETC, which will be set to ch mod 644 by defualt, and there is no need to change the setting
once the config file is on your unit, you should then see the plugin in this case, CCcam,
baz
Units; VU+Ultimo/duo/DM800/7020HD/tm9100
1.2 channel master/quad feedhorn/36volt /vbox
1 fixed dish, and 1 motorized 1mtr dish
and a pile of redundant cards/cams
Do you leave out the mipsel. ipk at the end, do you just put 2.1.1 in TMP.