VU+ Solo SE v2 Tuner problem

[abu baniaz]

There was a bug that affected twin tuner modules on the Vu receivers. I am not sure if your receiver was affected. We added a workaround for them.

I have looked the bug section, one of the posts said the bug only affected receivers with three tuners. So that is ruled out.

[dsayers]

I have looked the bug section, one of the posts said the bug only affected receivers with three tuners. So that is ruled out.

Wouldn't having dvb-t enabled aswel as having dvb-c be classed as more than 2 tuners enabled?

[abu baniaz]

No, 1+1 = 2
He only has two tuners on one card. The anomally about these tuners is you can set one to DVB-C and the other to DVB-T although it can only accept one signal wire.

[wizz_r]

That is tuner A, what about tuner B screenshot? I know you said it's the same.

Tuner B .......

TunerB.jpg

[abu baniaz]

Thanks.

I don't know why ABM is not showing for you. Maybe the debug log will show reason. A thread about debug logs is here
https://www.world-of-satellite.com/s...port-questions

Can you also issue this command using putty and post what comes up/is returned? I have made that guide easy to follow. Please try it.

opkg install enigma2-plugin-systemplugins-autobouquetsmaker

For me, this is what happens

Package enigma2-plugin-systemplugins-autobouquetsmaker (3.1+git524+fe614a9-r0) installed in root is up to date.

[wizz_r]

OK, I'll study the tutorial and give it a try.

Do you have a tutorial on Putty .....If so. can you please give me a link.

[Andy_Hazza]

I would personally flash ViX 5.2.001 again, setup as new, no restores of any kind. Set Tuner A & Tuner B as per my instruction above (leaving Net ID as 00000 in the Tuner Config). Then go into ABM and setup Virgin UK in the Providers and use your Net ID. Also just to confirm, you only have one signal wire going into the top of the Tuner card yeah?


Sent from my iPhone using Tapatalk

[wizz_r]

I would personally flash ViX 5.2.001 again, setup as new, no restores of any kind. Set Tuner A & Tuner B as per my instruction above (leaving Net ID as 00000 in the Tuner Config). Then go into ABM and setup Virgin UK in the Providers and use your Net ID. Also just to confirm, you only have one signal wire going into the top of the Tuner card yeah?


Sent from my iPhone using Tapatalk

Is there a tutorial to set up the latest image, because the only one I've seen is for an early VIX image install. and lots of things have changed....

At present I don't have an ABM, probably because I suspect my B Tuner is faulty, and I may have deleted the ABM plugin. The A Tuner works fine in the current config, but whether the B Tuner is enabled or not, I get a "Tuner failed" alert box. If I disable Tuner A and enable Tuner B,
I get no channels at all.

There is only one coaxial into the tuner, because it is a hybrid 2 in 1 tuner.

[abu baniaz]

Do you have a tutorial on Putty .....If so. can you please give me a link.

The link to the guide is in my signature. Here it is again
https://www.world-of-satellite.com/s...Linux-commands

It does not matter what you set the NetID to in tuner config, it has no relevance in the UK. Obviously easier to leave it at 00000.

Without intending to be rude, did you do anything with regards to installing/uninstalling ABM that you have not mentioned?

[abu baniaz]

I may have deleted the ABM plugin.

This will explain why you cannot see it. I wish you had said this earlier. Anyway,....

The command I gave above will install it again. Please try it. You will need to restart after installing it.

I am inclined to believe your tuner is faulty. It isn't an ABM issue as it is failing to tune without you using ABM.

[wizz_r]

The link to the guide is in my signature. Here it is again
https://www.world-of-satellite.com/s...Linux-commands

Thanks .....

It does not matter what you set the NetID to in tuner config, it has no relevance in the UK. Obviously easier to leave it at 00000.

OK......

Without intending to be rude, did you do anything with regards to installing/uninstalling ABM that you have not mentioned?

Your not...
The only ABM I see in Install plugins/extensions is autobouquets (2.2+git131). Isn't this a Sat plugin ?

[abu baniaz]

It is in "system plugins" not "extensions" in the installation menu when doing it by the graphical user interface. Will only show if system recognises it has been uninstalled correctly

Something must have got messed up when you tried to uninstall ABM. What do you want to do now? Start afresh (as suggested by Andy_Hazza) or re-install ABM using the command line?

[wizz_r]

It is in "system plugins" not "extensions" in the installation menu when doing it by the graphical user interface. Will only show if system recognises it has been uninstalled correctly

Something must have got messed up when you tried to uninstall ABM. What do you want to do now? Start afresh (as suggested by Andy_Hazza) or re-install ABM using the command line?

I'm struggling with PSFTP its asking me for a host name, using "open host.name" to connect ??

To start again, I could do with an up to date install guide, the only one I have is a very early one and too much has changed...... Do you know where there is one ?

[abu baniaz]

We are not file transferring. There is no need for PSFTP

[abu baniaz]

To start again...

Flash image using image manager, it is easier than using USB (guide in my signature)
After it restarts, do not restore settings or plugins
Ignore the prompt about installing plugins at this stage

Setup your tuner A as you pictured.
Disable tuner B. it is faulty

Install your softcam
Transfer your cam config files using FTP

Blue > Vix > softcam manager
Enable cam start up.
Start cam

Restart receiver.

Set ABM as you have now. Run ABM