Hello Guest, if you are reading this it means you have not registered yet. Please take a second, Click here to register, and in a few simple steps you will be able to enjoy our community and use our OpenViX support section.
Results 1 to 9 of 9

Thread: Back to Back Zapped timers not working

  1. #1

    Title
    Junior Member
    Join Date
    Dec 2012
    Posts
    20
    Thanks
    7
    Thanked 1 Time in 1 Post

    Back to Back Zapped timers not working

    Hi,

    I have created 3 zapped timers for programs across 3 channels but they don't appear to be working despite being enabled.

    I have tried disabling the conflict timer detection but it's still not working. Individual zapped timers are working fine, just not the consecutive zapped timers.

    I'm using vix image 5.0.027.

    Any ideas what I am doing wrong?
    VU+ Ultimo

  2. #2
    adm's Avatar
    Title
    Forum Supporter
    Donated Member
    Join Date
    Sep 2014
    Location
    Southend on Sea, UK
    Posts
    1,697
    Thanks
    67
    Thanked 668 Times in 522 Posts
    Quote Originally Posted by theredindian View Post
    Hi,

    I'm using vix image 5.0.027.

    Any ideas what I am doing wrong?
    Possibly, timer bug fixes in 5.0.28 onwards

    See post number #32 onwards in the following thread
    http://www.world-of-satellite.com/sh...x-images/page3
    Xtrend ET10K, 2 x satellite tuners 28.2 (Sky FTA), 2 x hybrid (UK Freeview), Zgemma H9S (satellite)

  3. #3
    birdman's Avatar
    Title
    Moderator
    Join Date
    Sep 2014
    Location
    Hitchin, UK
    Posts
    7,858
    Thanks
    239
    Thanked 1,673 Times in 1,318 Posts
    Quote Originally Posted by theredindian View Post
    Hi,

    I have created 3 zapped timers for programs across 3 channels but they don't appear to be working despite being enabled.
    In what way do they not work?
    • None of them is handled?
    • One of them is handled?
    • There is an issue with setting them?


    I have tried disabling the conflict timer detection
    To what intent (that's the reason for my third query above).

    Individual zapped timers are working fine, just not the consecutive zapped timers.
    Could you define what you mean by "consecutive zapped timers"?
    Are you setting up three timers for one hour programmes but with gaps between them of hours or are these three programmes that run such that one starts immediately the previous one finishes?

    Any ideas what I am doing wrong?
    Not without some detail to enable a reproduction.
    MiracleBox Prem Twin HD - 2@DVB-T2 + Xtrend et8000 - 5(incl. 2 different USBs)@DVB-T2[terrestrial - UK Freeview HD, Sandy Heath] - LAN/USB-stick/HDD

  4. #4
    birdman's Avatar
    Title
    Moderator
    Join Date
    Sep 2014
    Location
    Hitchin, UK
    Posts
    7,858
    Thanks
    239
    Thanked 1,673 Times in 1,318 Posts
    Quote Originally Posted by adm View Post
    Possibly, timer bug fixes in 5.0.28 onwards
    Unlikely to be the issue here as that's to do with the mechanism for enacting a timer. With that bug they should still run, but might be a little late in doing so (which doesn't sound as though ii's what is happening).
    MiracleBox Prem Twin HD - 2@DVB-T2 + Xtrend et8000 - 5(incl. 2 different USBs)@DVB-T2[terrestrial - UK Freeview HD, Sandy Heath] - LAN/USB-stick/HDD

  5. #5

    Title
    Junior Member
    Join Date
    Dec 2012
    Posts
    20
    Thanks
    7
    Thanked 1 Time in 1 Post
    Quote Originally Posted by birdman View Post
    In what way do they not work?
    • None of them is handled?
    • One of them is handled?
    • There is an issue with setting them?


    To what intent (that's the reason for my third query above).

    Could you define what you mean by "consecutive zapped timers"?
    Are you setting up three timers for one hour programmes but with gaps between them of hours or are these three programmes that run such that one starts immediately the previous one finishes?

    Not without some detail to enable a reproduction.
    If I set 3 zapped timers to run as follows none of them will execute;

    1. Timer 1 zap BBC 1 HD from 17:59
    2. Timer 2 zap BBC London from 18.29
    3. Timer 3 zap channel 4 HD from 18.59


    The timers will be in my list and you can see them in the epg guide. But for some reason it doesn't execute.

    I think it might be because the timers are set to start a minute before the program starts hence the slight overlap. So I tried disabling the timer conflict detection. But that did not work either.

    There might be a bug with this particular image release as the problem only started after updating around 4 weeks ago.

    I will try updating to the latest release as see if that resolves the problem.
    VU+ Ultimo

  6. #6
    adm's Avatar
    Title
    Forum Supporter
    Donated Member
    Join Date
    Sep 2014
    Location
    Southend on Sea, UK
    Posts
    1,697
    Thanks
    67
    Thanked 668 Times in 522 Posts
    Just as an experiment with build 5.0.029 I found 3 programs on 3 different channels that started within 10 minutes of each other and set a zap timer for each of them - and then watched a 4th channel. All 3 zap timers changed channel for me. When the 2nd zap occurred the 1st program was still running but the box changed channels and when the 3rd zap occurred both the 1st and 2nd programs were still running and the box changed channels again as expected.
    Xtrend ET10K, 2 x satellite tuners 28.2 (Sky FTA), 2 x hybrid (UK Freeview), Zgemma H9S (satellite)

  7. The Following User Says Thank You to adm For This Useful Post:

    theredindian (24-10-17)

  8. #7
    adm's Avatar
    Title
    Forum Supporter
    Donated Member
    Join Date
    Sep 2014
    Location
    Southend on Sea, UK
    Posts
    1,697
    Thanks
    67
    Thanked 668 Times in 522 Posts
    Quote Originally Posted by birdman View Post
    Unlikely to be the issue here as that's to do with the mechanism for enacting a timer. With that bug they should still run, but might be a little late in doing so (which doesn't sound as though ii's what is happening).
    On the image with the bug doesn't a record timer still work because it has both a start and end time and if the end time isn't reached the timer will still kick in?
    With a zap only timer there is no end time - or just the start and end times are the same?
    Xtrend ET10K, 2 x satellite tuners 28.2 (Sky FTA), 2 x hybrid (UK Freeview), Zgemma H9S (satellite)

  9. #8

    Title
    Junior Member
    Join Date
    Dec 2012
    Posts
    20
    Thanks
    7
    Thanked 1 Time in 1 Post
    Looks like there was a bug in that particular image release as it seems to be working fine after updating to the latest version
    VU+ Ultimo

  10. #9
    birdman's Avatar
    Title
    Moderator
    Join Date
    Sep 2014
    Location
    Hitchin, UK
    Posts
    7,858
    Thanks
    239
    Thanked 1,673 Times in 1,318 Posts
    Quote Originally Posted by adm View Post
    On the image with the bug doesn't a record timer still work because it has both a start and end time and if the end time isn't reached the timer will still kick in?
    With a zap only timer there is no end time - or just the start and end times are the same?
    You're probably (almost certainly) right. For some reason I was thinking a Zap timer had an end time too (which I suppose would make it a "reserve tuner" timer...)
    MiracleBox Prem Twin HD - 2@DVB-T2 + Xtrend et8000 - 5(incl. 2 different USBs)@DVB-T2[terrestrial - UK Freeview HD, Sandy Heath] - LAN/USB-stick/HDD

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
This website uses cookies
We use cookies to store session information to facilitate remembering your login information, to allow you to save website preferences, to personalise content and ads, to provide social media features and to analyse our traffic. We also share information about your use of our site with our social media, advertising and analytics partners.