Gigablue Quad 4K & UE 4K
.........FBC Tuners:
------------------> GT-Sat unicable LNB to 1.5M dish(28.2E)
------------------> Gigablue unicable LNB to 80 cm dish(19.2E)
.......................> FBC & DVB-S2X into 90cm dish (27.5W) Opticum robust Unicable LNB
AX HD61, Edision Osmio 4K+, Zgemma H9Combo, Octagon SF8008 , gbtrio4k, h9se using unicable ports
Zgemma H9 C/S into Giga4K
New drivers coming thick and fast now. It's the vtuner bit that interests me, will test tomorrow probably.
NEW: Driver (Driver) update Octagon SF4008 - 15.05.17
Testing by FTP: linuxtv.ko to lib/modules 4.1.37/extra/ and restart the box.
================================================== ======================
[Release note]
20170515
1. Issue [SF4008-i-75] mute symbol in standby is fixed
2. Issue [SF4008-i-56] viasat ci Modul is fixed
INFO: 4 x VTuner (USB) possible (4 x Virtual USB tuner possible)
================================================== == ============================
Code:http://octagon-forum.eu /test-team/sf4008/sf4008-drivers-4.1.37-6.3.0-20170515.zip
bassethound (16-05-17)
Looks like PLS Combo is a hardware issue. Silabs not capable apparently. So far only one transponder transmitting in this mode.
Yes, too bad about that.
I quickly tested vtuner and was able to record from the single DVB-C tuner in the third slot and also DVB-C from a remote box, both recordings ok now.
bassethound (16-05-17),el bandido (15-05-17),Tunder (16-05-17)
NEW: Driver update Octagon SF4008 - 17.05.17
================================================== =================
[release Note]
1. the number of supported vtuner: 4 -> 8
-> Info: Total 11 tuner support at the sametime!
2. [SF4008-I-71] ATSC type not accepted by vtuner is fixed
3. [SF4008-i-77] DVB-T2 is not accepted by Vtuner is fixed
4. Minor bug fix.
No, 14 is a couple of versions of driver behind now.
Last edited by maxben; 18-05-17 at 00:06.
Still does not support simultaneous tuners for me.1. VTuner Support increased to 8 (VTuner: virtual USB Tuner)
-> Info: Total simultaneous 11 Tuner Support!
Tuner 1-2 DVB-S2 dual tuner slot 1
Tuner 3 DVB-C single tuner use slot 2
Tuner 4 Sundtek DVB-C USB tuner
Tuner 5 Sundtek DVB-S2 USB tuner
So 5 tuners in total all working individually.
I tried on OpenVix 014 with new driver manually installed and OpenATV of today with new driver.
My testing method is as follows:-
1. Start recording 1 channel
2. Change channel to a different transponder and start another recording, both recordings at this point progress normally.
3. Change channel again to a different transponder and channel shows ok but the problem is that one of the recordings stops recording at that time.
So at the moment this seems to me that is 'simultaneous' tuner use is still not working!
Anyone else tried this feature ?
I've sent this report to Octagon.
john doe (18-05-17)
Thanks Huevos, I also posted on their support forum.
skippie (29-05-17)
As far as I can tell, there have been 2 driver updates since 5.0.014, and are in the latest 5.0.016 image.
NEW: Driver (Driver) update Octagon SF4008 - 23.06.17
FTP to
/lib/modules/4.1.37/extra
and restart the box.
================================================== =============
[ ReleaseNote ]
-. Tuner driver updated:
-> LNA On / Off function added. (Low Noise Amplifier)
. CI improved
. CA improved
. Run STB fixed.
-. Unlug CI fix.
-. Plug CI fix.
-. Video stop fix.
-. CA + CI use at same time fix.
================================================== =================
Code:http://octagon-forum.eu/test-team/sf4008/sf4008-drivers-4.1.37-6.3.0-20170623.zip
bassethound (24-06-17),khan888 (24-06-17),mrxbox360 (24-06-17)
just done mine & so far so good