Hi I note that I no longer have any signal on 4.8E. I have tested the other sites from 28.2E to 0.8W and all looked to be working fine. I can't see anything on the Net or on this forum saying they have a problem. Any help appreciated.
Hi I note that I no longer have any signal on 4.8E. I have tested the other sites from 28.2E to 0.8W and all looked to be working fine. I can't see anything on the Net or on this forum saying they have a problem. Any help appreciated.
[COLOR="#FF0000"]Vu+ Ultimo - 1.1m Techomate 2600 motorised dish & a fixed Sky dish - 3.9.6 Kernal - Drivers 24/11/2015 - Image Was openvix-5.0.020 - CCCam 2.3 - 1TB Hard drive - Connected to Network using ethernet cable - Skin Vix-Night HD
Maybe weather related or we're slightly out of alignment?
If I use Signal Finder I get a lock on 11766 H 27500 3/4 but say SVT1 HD is currently at 0% - that same channel works for me on Thor.
My dish is much smaller than yours though so possibly I never got 4.8e before trying today. (sorry!)
Last edited by aido; 22-11-16 at 17:42.
frankblueking (22-11-16)
Thanks Nick If the dish was out of alignment would the other sats also have a problem? 0.8W works fine as does 13, 16 19 and 28.2E. Confusing but we have had some strongish winds recently and maybe the alignment has changed. Frank
[COLOR="#FF0000"]Vu+ Ultimo - 1.1m Techomate 2600 motorised dish & a fixed Sky dish - 3.9.6 Kernal - Drivers 24/11/2015 - Image Was openvix-5.0.020 - CCCam 2.3 - 1TB Hard drive - Connected to Network using ethernet cable - Skin Vix-Night HD
when was the last time you updated your satellite settings , transponders change quite regular maybe your settings need up dating
4.8e is harder to pick up than those other sats you mentioned so slight movement of the dish could affect it and not the others.
VU+ Ultimo 4K 3TB, 1x Twin DVBS-2 FBC / 1x DVB-C FBC/ 1x Twin DVB-T2.
VU+ Solo4k 2TB, 2xFBC-S2, 2xC/T2, 1x Sundtek .
1m Motorised Single LNB Dish, 60cm Fixed Octo LNB Dish.
Samsung 65HU8500 with SEK-3500, Denon AVR-X2200W 5.1.2.
Oppo UDP-203
Panasonic 55VT50.
Zidoo X9S
Amazon Fire TV 4k & Amazon Fire TV (SPMC sideloaded).
I have scanned today so not sure it is out of date settings. I am now convinced the dish must have moved in the wind although I tried adjusting the longitude and latitude to see if that made a difference, it didn't make a lot of difference. If my memory serves me correctly I marked the mast for direction 0.00 so that could give a clue. Thanks for your help.
[COLOR="#FF0000"]Vu+ Ultimo - 1.1m Techomate 2600 motorised dish & a fixed Sky dish - 3.9.6 Kernal - Drivers 24/11/2015 - Image Was openvix-5.0.020 - CCCam 2.3 - 1TB Hard drive - Connected to Network using ethernet cable - Skin Vix-Night HD
[COLOR="#FF0000"]Vu+ Ultimo - 1.1m Techomate 2600 motorised dish & a fixed Sky dish - 3.9.6 Kernal - Drivers 24/11/2015 - Image Was openvix-5.0.020 - CCCam 2.3 - 1TB Hard drive - Connected to Network using ethernet cable - Skin Vix-Night HD
Hi Frank,some time the motor goes off from orbit,when motor is of from orbit then all satellite have been effected ,so you loosing signal from all satellites ,if the sat installer have done good job one beginning ,and obviously and configuration mode have choose USALS,and you use to watch at 4.8 east, you can reset the motor from factory default,deleted all errors , how you can do that on any satellite box Enigma 2 linux ,menu-setup-service searching-positioner setup-and highlight Goto then 000.0 then press green button,dependent on your box what option that image have to send the motor 0 degrees ,same on my screen shot,then motor goes 0 degrees, wait till stop , when motor is stop at 0 degrees then unplug the coax cable from back of receiver wait 10 seconds ,and press all exit from the menu,then re plug again the cable , ten give command to go 4.8 east and see did you got picture or no , if not then motor need alignment,
Astra 4A---4.8 east ---120cm Nordic beam (UK is outside intended service area)
Astra 4A ---4.8 east ---80cm European beam
regards Nick
frankblueking (23-11-16)