Hello Guest, if you are reading this it means you have not registered yet. Please take a second, Click here to register, and in a few simple steps you will be able to enjoy our community and use our OpenViX support section.
Page 1 of 3 123 LastLast
Results 1 to 15 of 32

Thread: My xtrend 8000 seems to have frozen on Vix bootup

  1. #1

    Title
    Forum Supporter
    Donated Member
    Join Date
    Jun 2013
    Posts
    1,255
    Thanks
    38
    Thanked 98 Times in 91 Posts

    My xtrend 8000 seems to have frozen on Vix bootup

    Ok so i wanted to do a fresh flash to the latest VIx but for some reason after the flashing stage, it loads up openvix and then i just get a spinning logo, ten freezes for 10 seconds, then the logo spins again, it has been doing it every time i boot up. Even when i boot up without flashing it just gets stuck with the logo spinning and then freezing again. I have tried the latest openvix and the one of the old versions.
    My receiver is stuck whatever i do. It just gets stuck on bootup whatever happens
    I am out of ideas now.
    Thanks

  2. #2
    twol's Avatar
    Title
    Moderator
    Join Date
    Apr 2012
    Posts
    8,618
    Thanks
    1,009
    Thanked 2,964 Times in 2,305 Posts
    Sounds like boot crash
    Telnet into boxes ip address , then enter
    Init 4 ........wait 60 secs for everything to be stopped
    enigma2

    Look through through the log until you see the problem
    Gigablue Quad 4K & UE 4K
    .........FBC Tuners:
    ------------------> GT-Sat unicable LNB to 1.5M dish(28.2E)
    ------------------> Gigablue unicable LNB to 80 cm dish(19.2E)
    .......................
    Vu+ Uno4KSE, Dreambox dm900
    AX HD61, Edision Osmio 4K+, Zgemma H9Combo, Octagon SF8008 , gbtrio4k, h9se using unicable ports
    Zgemma H9 C/S into Giga4K

  3. #3

    Title
    Forum Supporter
    Donated Member
    Join Date
    Jun 2013
    Posts
    1,255
    Thanks
    38
    Thanked 98 Times in 91 Posts
    Quote Originally Posted by twol View Post
    Sounds like boot crash
    Telnet into boxes ip address , then enter
    Init 4 ........wait 60 secs for everything to be stopped
    enigma2

    Look through through the log until you see the problem
    How tho. I can't get it connected to my network. It doesn't even pass that stage. It's like openvix is corrupted. Is there anyway I can get get it to boot into a different mode or something?

  4. #4

    Title
    Forum Supporter
    Donated Member
    Join Date
    Jul 2014
    Location
    God Knows
    Posts
    1,694
    Thanks
    582
    Thanked 266 Times in 247 Posts
    have you tried to flash again?
    PLEASE DO NOT PM IN REGARDS TO CS TALK OR OTHER ILEGAL MATTERS. IT WILL BE REPORTED TO THE ADMINS

  5. #5

    Title
    Forum Supporter
    Donated Member
    Join Date
    Jun 2013
    Posts
    1,255
    Thanks
    38
    Thanked 98 Times in 91 Posts
    Quote Originally Posted by john doe View Post
    have you tried to flash again?
    Yh i have tried flashing, same thing happens.. is there anyway i can upload a video of what happening?
    It just spins in the corner and then screen goes black. I tried this vix and the last series of openvix same thing happens. I have no HDD connected to it can not be something to do with that.
    Really strange.

  6. #6
    Andy_Hazza's Avatar
    Title
    Moderator
    Join Date
    Oct 2012
    Location
    Derbyshire, UK
    Posts
    7,287
    Thanks
    2,855
    Thanked 2,126 Times in 1,752 Posts
    Have you tried flashing the bootloader first then try flashing the image again after?


    Sent from my iPhone using Tapatalk
    Vu+ Ultimo 4K with 3TB HDD, Dual FBC (Sat) tuners, 1x Twin Hybrid DVB-C/T/T2 tuner
    Vu+ Solo 4K with 1TB HDD, Dual FBC (Sat) tuners, 1x Hybrid DVB-C/T/T2 tuner
    Vu+ Solo 2 with 1TB HDD 'White Edition', 2x DVB-S2 tuners
    Mut@nt HD2400 with 1TB HDD, 4x DVB-S2 tuners
    Fixed 28.2E Technomate 65cm Mesh Satellite Dish with Inverto Unicable II/JESS LNB and Inverto Unicable Splitter
    Fixed 28.2E Sky Zone 1 45cm Satellite Dish with Octo LNB
    (All receivers installed with the latest Dev build)

  7. #7

    Title
    Forum Supporter
    Donated Member
    Join Date
    Jun 2013
    Posts
    1,255
    Thanks
    38
    Thanked 98 Times in 91 Posts
    Quote Originally Posted by Andy_Hazza View Post
    Have you tried flashing the bootloader first then try flashing the image again after?


    Sent from my iPhone using Tapatalk
    Oh sorry Andy. Have no idea what bootloader does I have never needed to do anyting with that?
    How do i do this? and what does this do?

  8. #8
    Andy_Hazza's Avatar
    Title
    Moderator
    Join Date
    Oct 2012
    Location
    Derbyshire, UK
    Posts
    7,287
    Thanks
    2,855
    Thanked 2,126 Times in 1,752 Posts
    I just wondered if something has got corrupted. Is pretty much same procedure as if you were flashing an image but it literally only takes a few seconds to complete.
    Bootloader can be found here. Go with the latest one. >> http://www.openvix.co.uk/index.php/d...0-bootloaders/


    Sent from my iPhone using Tapatalk
    Vu+ Ultimo 4K with 3TB HDD, Dual FBC (Sat) tuners, 1x Twin Hybrid DVB-C/T/T2 tuner
    Vu+ Solo 4K with 1TB HDD, Dual FBC (Sat) tuners, 1x Hybrid DVB-C/T/T2 tuner
    Vu+ Solo 2 with 1TB HDD 'White Edition', 2x DVB-S2 tuners
    Mut@nt HD2400 with 1TB HDD, 4x DVB-S2 tuners
    Fixed 28.2E Technomate 65cm Mesh Satellite Dish with Inverto Unicable II/JESS LNB and Inverto Unicable Splitter
    Fixed 28.2E Sky Zone 1 45cm Satellite Dish with Octo LNB
    (All receivers installed with the latest Dev build)

  9. #9

    Title
    Forum Supporter
    Donated Member
    Join Date
    Jun 2013
    Posts
    1,255
    Thanks
    38
    Thanked 98 Times in 91 Posts
    Quote Originally Posted by Andy_Hazza View Post
    Have you tried flashing the bootloader first then try flashing the image again after?


    Sent from my iPhone using Tapatalk


    on the openvix website i see two things

    ET-8×00 Bootloaders
    Et8000 Cfe 20140214 (153.6k)
    LAST MODIFIED FEBRUARY 16, 2015 AT 4:17 PM
    Et8000 Cfe 20140821 (155.7k)
    LAST MODIFIED FEBRUARY 16, 2015 AT 4:17 PM

    Would i need to do something with this?

  10. #10

    Title
    Forum Supporter
    Donated Member
    Join Date
    Jun 2013
    Posts
    1,255
    Thanks
    38
    Thanked 98 Times in 91 Posts
    Quote Originally Posted by Andy_Hazza View Post
    I just wondered if something has got corrupted. Is pretty much same procedure as if you were flashing an image but it literally only takes a few seconds to complete.
    Bootloader can be found here. Go with the latest one. >> http://www.openvix.co.uk/index.php/d...0-bootloaders/


    Sent from my iPhone using Tapatalk
    Hey andy

    So it is exactly the same thing as flashing an image. So what would happen after this? Would it just go back to its factory settings? Also, which one do i pick?

  11. #11
    Andy_Hazza's Avatar
    Title
    Moderator
    Join Date
    Oct 2012
    Location
    Derbyshire, UK
    Posts
    7,287
    Thanks
    2,855
    Thanked 2,126 Times in 1,752 Posts
    Go with the latest one dated 21/08/2014.


    Sent from my iPhone using Tapatalk
    Vu+ Ultimo 4K with 3TB HDD, Dual FBC (Sat) tuners, 1x Twin Hybrid DVB-C/T/T2 tuner
    Vu+ Solo 4K with 1TB HDD, Dual FBC (Sat) tuners, 1x Hybrid DVB-C/T/T2 tuner
    Vu+ Solo 2 with 1TB HDD 'White Edition', 2x DVB-S2 tuners
    Mut@nt HD2400 with 1TB HDD, 4x DVB-S2 tuners
    Fixed 28.2E Technomate 65cm Mesh Satellite Dish with Inverto Unicable II/JESS LNB and Inverto Unicable Splitter
    Fixed 28.2E Sky Zone 1 45cm Satellite Dish with Octo LNB
    (All receivers installed with the latest Dev build)

  12. #12

    Title
    Forum Supporter
    Donated Member
    Join Date
    Jun 2013
    Posts
    1,255
    Thanks
    38
    Thanked 98 Times in 91 Posts
    Quote Originally Posted by Andy_Hazza View Post
    Go with the latest one dated 21/08/2014.


    Sent from my iPhone using Tapatalk
    ok i will try that now. So once i have done that, i can take the usb out and then put latest version of vix and try again.
    What would load up when i flash the bootloader thing?

  13. #13
    Andy_Hazza's Avatar
    Title
    Moderator
    Join Date
    Oct 2012
    Location
    Derbyshire, UK
    Posts
    7,287
    Thanks
    2,855
    Thanked 2,126 Times in 1,752 Posts
    Yeah flash bootloader first then take usb out n power off. Then insert usb with image on n power on n flash latest ViX image.


    Sent from my iPhone using Tapatalk
    Vu+ Ultimo 4K with 3TB HDD, Dual FBC (Sat) tuners, 1x Twin Hybrid DVB-C/T/T2 tuner
    Vu+ Solo 4K with 1TB HDD, Dual FBC (Sat) tuners, 1x Hybrid DVB-C/T/T2 tuner
    Vu+ Solo 2 with 1TB HDD 'White Edition', 2x DVB-S2 tuners
    Mut@nt HD2400 with 1TB HDD, 4x DVB-S2 tuners
    Fixed 28.2E Technomate 65cm Mesh Satellite Dish with Inverto Unicable II/JESS LNB and Inverto Unicable Splitter
    Fixed 28.2E Sky Zone 1 45cm Satellite Dish with Octo LNB
    (All receivers installed with the latest Dev build)

  14. #14

    Title
    Forum Supporter
    Donated Member
    Join Date
    Jun 2013
    Posts
    1,255
    Thanks
    38
    Thanked 98 Times in 91 Posts
    Quote Originally Posted by Andy_Hazza View Post
    Yeah flash bootloader first then take usb out n power off. Then insert usb with image on n power on n flash latest ViX image.


    Sent from my iPhone using Tapatalk
    ok so i extracted the file onto the USb stick but it did not come up with any message asking me to press OK
    IS it supposed to ask me something?

  15. #15

    Title
    Forum Supporter
    Donated Member
    Join Date
    Jun 2013
    Posts
    1,255
    Thanks
    38
    Thanked 98 Times in 91 Posts
    I found these instructions on the xtrend website

    1. Download the attached zip file.

    2. Unzip and copy + paste the et8000 folder on to your USB Stick

    3. Insert USB Stick to your ET8000.

    4. When you see the message "Flash Image?" on your front display, press the CH 'down' key (instead of the 'up' key which you would normally use to flash an image).

    Is this correct? I always press OK when it asks for flash

Page 1 of 3 123 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
This website uses cookies
We use cookies to store session information to facilitate remembering your login information, to allow you to save website preferences, to personalise content and ads, to provide social media features and to analyse our traffic. We also share information about your use of our site with our social media, advertising and analytics partners.