Hello Guest, if you are reading this it means you have not registered yet. Please take a second, Click here to register, and in a few simple steps you will be able to enjoy our community and use our OpenViX support section.
Results 1 to 9 of 9

Thread: No western satellites on TM nano oe tuner

  1. #1

    Title
    Junior Member
    Join Date
    Apr 2014
    Posts
    18
    Thanks
    5
    Thanked 0 Times in 0 Posts

    No western satellites on TM nano oe tuner

    I have the latest vhannibals motor satellites and channels list installed but when I go the tuner configuration (advanced mode) I don't seem to access any western satellites from 1 west to 45 west, all I see 3.1 east to 75 east satellites. How I can get access to the western satellites in order to be able to manually tune them. Any help is greatly appreaciated.


  2. #2
    abu baniaz's Avatar
    Title
    Moderator
    Join Date
    Sep 2010
    Location
    East London
    Posts
    23,541
    Thanks
    6,517
    Thanked 9,224 Times in 6,287 Posts
    "Latest" is ambiguius.
    Which image are you using. Please specify thename and build number.
    Vhannibals latest motorised one is dated 20/04/2014. Is this the one you are using?

    You may wish to use a satellites.xml from
    Code:
    http://satellites-xml.org/
    and replace the one in Vhannibals one.

  3. The Following User Says Thank You to abu baniaz For This Useful Post:

    satnano (20-04-14)

  4. #3

    Title
    Junior Member
    Join Date
    Apr 2014
    Posts
    18
    Thanks
    5
    Thanked 0 Times in 0 Posts
    Many thanks Abu Baniaz, yes it is vhannibal 20th April one and I have replaced the satellites.xml via fizella, as you suggested, but I still can't see the western satellites as a choice in the tuner configuration menu. I can see 1.6 East till 75 East satellites and that is all.

  5. #4
    abu baniaz's Avatar
    Title
    Moderator
    Join Date
    Sep 2010
    Location
    East London
    Posts
    23,541
    Thanks
    6,517
    Thanked 9,224 Times in 6,287 Posts
    Try it this way, save the xml file in the same folder as your Vhannibal bouquet and then transfer the channel lists using Dreamset/Dreamboxedit.

    I've just tried Vhannibal's 20/4 and all the satellites are there. You are going past "all satellites" until you reach the western ones?

  6. #5

    Title
    Junior Member
    Join Date
    Apr 2014
    Posts
    18
    Thanks
    5
    Thanked 0 Times in 0 Posts
    I have already transferred vhannibal motorised channel list via dreamboxedit. In tuner config, I am going through all the eastern satlleites then "all satellites 1" through to "all satellites 4" then the eastern satellites start again, there is no sign of western satellites.
    Last edited by satnano; 20-04-14 at 21:37.

  7. #6

    Title
    Junior Member
    Join Date
    Apr 2014
    Posts
    18
    Thanks
    5
    Thanked 0 Times in 0 Posts
    A proper restart by switching the receiver off from back button and then on, brought the western satellites. Sorry for the bother from a newbie.

  8. #7
    Rob van der Does's Avatar
    Title
    ViX Beta Tester
    Join Date
    Apr 2010
    Location
    The Netherlands & France
    Posts
    36,270
    Thanks
    1,720
    Thanked 9,461 Times in 6,675 Posts
    Quote Originally Posted by satnano View Post
    A proper restart by switching the receiver off from back button and then on,...
    Pulling the plug is not a proper restart; it can even kill your box. Always bring the box down (to deep sleep) before doing that.
    Anyway: an Enigma2 restart after changing the satellites.xml would have done the trick.

    Help asked via PM will be ignored.
    The forum is there for help and all will benefit from your questions.
    NO CARD SHARING TALK WILL BE TOLERATED, LAN OR WAN, IN OPEN FORUM OR PM !

    English is not my native tongue.
    I apologise for all my grammar, spelling and idiom errors.

  9. #8

    Title
    Junior Member
    Join Date
    Apr 2014
    Posts
    18
    Thanks
    5
    Thanked 0 Times in 0 Posts
    Quote Originally Posted by Rob van der Does View Post
    Pulling the plug is not a proper restart; it can even kill your box. Always bring the box down (to deep sleep) before doing that.
    Anyway: an Enigma2 restart after changing the satellites.xml would have done the trick.
    Thanks Rob van der, Believe me I did restart Enigma2 via Dreamboxedit after installing Vhannibal 20th April file but this didn't load western satellites for some reason!!

  10. #9

    Title
    ViX Beta Tester
    Join Date
    Apr 2011
    Location
    Ireland
    Posts
    2,051
    Thanks
    404
    Thanked 669 Times in 548 Posts
    Just use the remote
    Zgemma H7S running OpenVIX 6.2, Darkmotor, Triax TD110 dish, Inverto Black Ultra dual lnb
    LG 50UM7450 4K TV, Pioneer VSX-534 Atmos AVR , Panasonic UB820 region free 4K Bluray & a PS4.

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
This website uses cookies
We use cookies to store session information to facilitate remembering your login information, to allow you to save website preferences, to personalise content and ads, to provide social media features and to analyse our traffic. We also share information about your use of our site with our social media, advertising and analytics partners.