My posts contain my own personal thoughts and opinions, they do not represent those of any organisation or group but my own.
If you don't like what I post, Don't read it.
SIMPLES.
VU+ DUO² (Triple S2 tuners) VIX, 750gb
TM-Nano 2 Super, 320gb
GigaBlue HD 800 UE Plus VIX
TM-Single VIX IT'S ALIVE
Octagon SF8 VIX (751MHz bootloader)
MARA M9
Harmony 700
DGS108 GBLAN, DIY NAS (8TB) XPEnology
1.1m dish, 0.1db Quad LNB, GTSAT DM14MG motor
80cm dish, 2x 0.1db LNB + 1x Quad 0.2db LNB, Disqec 4/1.
Found a user manual for Fancontrol2. Might be useful to some
FanControl2 Manual.pdf
VU+ DUO² (Triple S2 tuners) VIX, 750gb
TM-Nano 2 Super, 320gb
GigaBlue HD 800 UE Plus VIX
TM-Single VIX IT'S ALIVE
Octagon SF8 VIX (751MHz bootloader)
MARA M9
Harmony 700
DGS108 GBLAN, DIY NAS (8TB) XPEnology
1.1m dish, 0.1db Quad LNB, GTSAT DM14MG motor
80cm dish, 2x 0.1db LNB + 1x Quad 0.2db LNB, Disqec 4/1.
Larry-G (31-03-14)
My posts contain my own personal thoughts and opinions, they do not represent those of any organisation or group but my own.
If you don't like what I post, Don't read it.
SIMPLES.
The DUO has no fancontrol at all. Only On/Off is supported.
Quite a lot of the boxes we support do support fancontrol2. Normally that plugin will only show in the feeds of a box if it is supported. But as we don't have all boxes to check, this might not be 100% correct.
And it is actually quite difficult to give an advise on the settings: it's more like being happy with what you do and see.
Speaking for myself, I like low temperatures; that's why I set the temperature rather low. See the screenies of my Ultimo settings.
Help asked via PM will be ignored.
The forum is there for help and all will benefit from your questions.
NO CARD SHARING TALK WILL BE TOLERATED, LAN OR WAN, IN OPEN FORUM OR PM !
English is not my native tongue.
I apologise for all my grammar, spelling and idiom errors.
marty (31-03-14)
found this in the pdf so it looks like it works with both 3 & 4 pin fans
Function
Automatic regulation of a 3pin or 4pin (PWM) fan.
Based on the average temperature from the 2 highest temperature values.
Slowly regulation, because temperatures do not change too quickly and there should be no unnecessary CPU load.
Actually the Ultimo, Solo2 & DUO2 have only a 2-pin fan (so no real RPM-sensor). The sensor is emulated in software, hence the setting must be '3-pin'.
Help asked via PM will be ignored.
The forum is there for help and all will benefit from your questions.
NO CARD SHARING TALK WILL BE TOLERATED, LAN OR WAN, IN OPEN FORUM OR PM !
English is not my native tongue.
I apologise for all my grammar, spelling and idiom errors.
I have just set up my vu solo 2
With it on and watching TV the temp was sitting around 30 - 32
When I checked it this morning after being in standby it was at 36
Is this to high?
imho everything below 40 is ok.
standby by the way does not save a lot of energy... so there shouldn't be a big difference in temperature.
My posts contain my own personal thoughts and opinions, they do not represent those of any organisation or group but my own.
If you don't like what I post, Don't read it.
SIMPLES.
Best to add a power timer to shut box off.
There is absolutely no need to wakeup the box to do EPG at 4 am. Do it whenever it suits you.