VU+ DUO² (Triple S2 tuners) VIX, 750gb
TM-Nano 2 Super, 320gb
GigaBlue HD 800 UE Plus VIX
TM-Single VIX IT'S ALIVE
Octagon SF8 VIX (751MHz bootloader)
MARA M9
Harmony 700
DGS108 GBLAN, DIY NAS (8TB) XPEnology
1.1m dish, 0.1db Quad LNB, GTSAT DM14MG motor
80cm dish, 2x 0.1db LNB + 1x Quad 0.2db LNB, Disqec 4/1.
Will do and thanks for your help.
Sent from my iPhone using Tapatalk
I don't know about your TV but I can control my Pi with the TV's remote
No pissing about with keyboard and/or mouse
VU+ DUO² (Triple S2 tuners) VIX, 750gb
TM-Nano 2 Super, 320gb
GigaBlue HD 800 UE Plus VIX
TM-Single VIX IT'S ALIVE
Octagon SF8 VIX (751MHz bootloader)
MARA M9
Harmony 700
DGS108 GBLAN, DIY NAS (8TB) XPEnology
1.1m dish, 0.1db Quad LNB, GTSAT DM14MG motor
80cm dish, 2x 0.1db LNB + 1x Quad 0.2db LNB, Disqec 4/1.
I can disable it through webif.
Vix 3.0.808
Kernel 3.3.8
Drivers 2013-12-17
Webif Transcoding.jpg
grahammcm1888 (20-02-14)
So you're using the latest drivers and plugin
Help asked via PM will be ignored.
The forum is there for help and all will benefit from your questions.
NO CARD SHARING TALK WILL BE TOLERATED, LAN OR WAN, IN OPEN FORUM OR PM !
English is not my native tongue.
I apologise for all my grammar, spelling and idiom errors.
VU+ DUO² (Triple S2 tuners) VIX, 750gb
TM-Nano 2 Super, 320gb
GigaBlue HD 800 UE Plus VIX
TM-Single VIX IT'S ALIVE
Octagon SF8 VIX (751MHz bootloader)
MARA M9
Harmony 700
DGS108 GBLAN, DIY NAS (8TB) XPEnology
1.1m dish, 0.1db Quad LNB, GTSAT DM14MG motor
80cm dish, 2x 0.1db LNB + 1x Quad 0.2db LNB, Disqec 4/1.
Marty, Yeah the TV remote works fine with XBMC/Openelec. I can only assume this must be done via hdmi as I had my TV disconnected from my network and as far as I know the Pi does not have an Ir receiver (it was stuck behind the tv anyway) . Hopefully I will get this working tonight as it is doing my head in.
Just home guys and it would appear that I might not have the latest drivers as I only have a basic config page in the transcoding section which does allow the transcoding feature to be switched off.
So how do I install the latest driver ?!Untitled.jpg
Getting there slowly guys . I took TLW advice and turned off transcoding on the Duo2 and set the port on the rpi to 8001 and I can now get HD channels only. Its still pretty inconsistent and the rpi requires a reboot every second or third channel change. So I am hoping the driver update works and then I will change the port back to 8002 on the rpi and hopefully get SD and HD channels. Just need to know how to upgrade and install the new drivers!
Sent from my iPhone using Tapatalk
Get drivers from
unpack the files and ftp them to "/lib/modules/3.3.8/extra" (overwriting the existing files) and reboot the box (not an E2-restart).Code:http://archive.vuplus.com/download/drivers/
Help asked via PM will be ignored.
The forum is there for help and all will benefit from your questions.
NO CARD SHARING TALK WILL BE TOLERATED, LAN OR WAN, IN OPEN FORUM OR PM !
English is not my native tongue.
I apologise for all my grammar, spelling and idiom errors.
grahammcm1888 (20-02-14)
Rob I have downloaded the latest driver , ftp to duo in the correct folder and restarted the box but on the info page it still shows 17/12/13. Do I have to apply the update?
Sent from my iPad using Tapatalk
That is correct: that date will only be altered if the drivers are installed via an updated image. Do't worry about that: it's only cosmetic.
Help asked via PM will be ignored.
The forum is there for help and all will benefit from your questions.
NO CARD SHARING TALK WILL BE TOLERATED, LAN OR WAN, IN OPEN FORUM OR PM !
English is not my native tongue.
I apologise for all my grammar, spelling and idiom errors.
Ok I understand. However I still only have the option within Webif to enable or disable the transcoding feature with no advance config possible
OK, that'll be because the web-if is also old. So better use the box itself to make changes.
Help asked via PM will be ignored.
The forum is there for help and all will benefit from your questions.
NO CARD SHARING TALK WILL BE TOLERATED, LAN OR WAN, IN OPEN FORUM OR PM !
English is not my native tongue.
I apologise for all my grammar, spelling and idiom errors.
grahammcm1888 (20-02-14)
can I update the Webif interface?