Youll need to purchase the codecs to get sd working , dont need them for hd but youll get a lot of break up,
what I did was to make an Sd only bouquet and in the settings tell the plugin to only use 1 bouquet , that being the sd one obviously
Youll need to purchase the codecs to get sd working , dont need them for hd but youll get a lot of break up,
what I did was to make an Sd only bouquet and in the settings tell the plugin to only use 1 bouquet , that being the sd one obviously
I am having little success with this. The pi keeps crashing when I attempt to start live tv. I have tried ports 8001 and 8002 with no success. Playing movies or recordings from the duo2 is working fine. The problem is the time it takes the epg data to download. I cant get playing about with the setting as it is taking an hour each time the pi hangs .
Sent from my iPhone using Tapatalk
VU+ DUO² (Triple S2 tuners) VIX, 750gb
TM-Nano 2 Super, 320gb
GigaBlue HD 800 UE Plus VIX
TM-Single VIX IT'S ALIVE
Octagon SF8 VIX (751MHz bootloader)
MARA M9
Harmony 700
DGS108 GBLAN, DIY NAS (8TB) XPEnology
1.1m dish, 0.1db Quad LNB, GTSAT DM14MG motor
80cm dish, 2x 0.1db LNB + 1x Quad 0.2db LNB, Disqec 4/1.
grahammcm1888 (20-02-14)
You need to set the Epg to only download 1 day at a time, this will speed the process up for now. Raspberry Pi is a great device but of the cheap variety, somethings it will handle fantastically and others not so great.
I use an Ouya for my pleasure, it handles everything really well however it is common that the Epg can take some time across all platforms to download, some faster than others. I always found it annoying having to wait for the Epg to download every time I turned my box on so just cut it down to 1 day at a time and no its completed with 1 minute.
Last edited by duoduo; 20-02-14 at 08:47.
Vix image (usually latest) - VU Solo 4K- WD 1TB INTERNAL HDD - DVB-T Freeview, trialling IPTV options
If my response has helped you, don't forget to hit the thanks button below. I appreciate you appreciate me
I had already set the pi to download the epg to download after 2880 hours (2days). The problem is when i have to reboot the epg download is started again. Marty what is your transcoding setup on your Duo2? And are you using the latest vix build as I am . I have read in some forums that the transcoding function does not work with the latest build (808 I think).
Sent from my iPad using Tapatalk
Make sure you have Transcoding turned off on your Duo2. Had the same problem with LiveTV on my S4 phone.
grahammcm1888 (20-02-14)
Transcoding can't be turned off (using the latest drivers and plugin): it's always enabled.
Help asked via PM will be ignored.
The forum is there for help and all will benefit from your questions.
NO CARD SHARING TALK WILL BE TOLERATED, LAN OR WAN, IN OPEN FORUM OR PM !
English is not my native tongue.
I apologise for all my grammar, spelling and idiom errors.
I'll post s screenshot later. At work until 1pm
VU+ DUO² (Triple S2 tuners) VIX, 750gb
TM-Nano 2 Super, 320gb
GigaBlue HD 800 UE Plus VIX
TM-Single VIX IT'S ALIVE
Octagon SF8 VIX (751MHz bootloader)
MARA M9
Harmony 700
DGS108 GBLAN, DIY NAS (8TB) XPEnology
1.1m dish, 0.1db Quad LNB, GTSAT DM14MG motor
80cm dish, 2x 0.1db LNB + 1x Quad 0.2db LNB, Disqec 4/1.
grahammcm1888 (20-02-14)
No problem I am also at work!
I presume that transcoding is always on on port 8001 and is preconfigured. I also assume that the transcoding feature in the transcoding plugin is for a secondary stream which you can define a port number within a range and set this stream up to your preferred config.
VU+ DUO² (Triple S2 tuners) VIX, 750gb
TM-Nano 2 Super, 320gb
GigaBlue HD 800 UE Plus VIX
TM-Single VIX IT'S ALIVE
Octagon SF8 VIX (751MHz bootloader)
MARA M9
Harmony 700
DGS108 GBLAN, DIY NAS (8TB) XPEnology
1.1m dish, 0.1db Quad LNB, GTSAT DM14MG motor
80cm dish, 2x 0.1db LNB + 1x Quad 0.2db LNB, Disqec 4/1.
VU+ DUO² (Triple S2 tuners) VIX, 750gb
TM-Nano 2 Super, 320gb
GigaBlue HD 800 UE Plus VIX
TM-Single VIX IT'S ALIVE
Octagon SF8 VIX (751MHz bootloader)
MARA M9
Harmony 700
DGS108 GBLAN, DIY NAS (8TB) XPEnology
1.1m dish, 0.1db Quad LNB, GTSAT DM14MG motor
80cm dish, 2x 0.1db LNB + 1x Quad 0.2db LNB, Disqec 4/1.
There are my setting, they are not the be all and end all you might be able to improve by playing about but these work for me
tran.jpg
VU+ DUO² (Triple S2 tuners) VIX, 750gb
TM-Nano 2 Super, 320gb
GigaBlue HD 800 UE Plus VIX
TM-Single VIX IT'S ALIVE
Octagon SF8 VIX (751MHz bootloader)
MARA M9
Harmony 700
DGS108 GBLAN, DIY NAS (8TB) XPEnology
1.1m dish, 0.1db Quad LNB, GTSAT DM14MG motor
80cm dish, 2x 0.1db LNB + 1x Quad 0.2db LNB, Disqec 4/1.
So I need to stick the pi to 8002 and configure the options on the duo2 accordingly?
Sent from my iPhone using Tapatalk