Ahah they cut-out the fix on dts-hd, fantastic, typical attitude by them.
Inviato dal mio GT-I9070 utilizzando Tapatalk
Ahah they cut-out the fix on dts-hd, fantastic, typical attitude by them.
Inviato dal mio GT-I9070 utilizzando Tapatalk
recordings are not fixed either
sent from Pipo M9 Pro
VU+ Ultimo 4k
Samsung Qled 90R
VU+ DUO² (Triple S2 tuners) VIX, 750gb
TM-Nano 2 Super, 320gb
GigaBlue HD 800 UE Plus VIX
TM-Single VIX IT'S ALIVE
Octagon SF8 VIX (751MHz bootloader)
MARA M9
Harmony 700
DGS108 GBLAN, DIY NAS (8TB) XPEnology
1.1m dish, 0.1db Quad LNB, GTSAT DM14MG motor
80cm dish, 2x 0.1db LNB + 1x Quad 0.2db LNB, Disqec 4/1.
the problem is : when you set recording before and after to 0 then the second or other recordings have no picture, only sound, or there's nothing at all. (0 recording)
for exemple : starting a recording at 14.00 for 10 mins till 14.10 is ok
next recording starts at 14.10 till whenever, well that recording is not right then. (recording on the same channel)
Set the recording setup to 1 min before and x-minutes after, then there is no problem
Last edited by skippie; 25-01-14 at 16:59.
yep, had lots of timer recording problems - switched back to driver from 2nd November.
Does anyone have an email address or web page for GigaBlue developers?
UStrange...I tested recordings without any kind of problem. What about your drive? How is your setup? And your situation about your cables? Softcam used? I tested these new drivers a lot coz I wanted to check if almost for recordings they fixed and I can saw they have done a good job. No problems at all now
Inviato dal mio GT-I9070 utilizzando Tapatalk
I had a problem yesterday with a timer recording which was 0 bytes length.
Today, I was recording the 6 nations rugby (from Irish DTT) - checked while recording and the recording was 0 bytes length and wouldn't play.
Stopped the recording then started it again - same issue.
Changed back to the old driver, rebooted, tried again - recorded fine.
The recording problems are intermittent and random - using the 02 November driver doesn't have these problems.
I have been using Quads now for 18 months.. and at least 3-4 hours of recordings every single day..
In ALL that time.. I have only ever had 1 recording fail.. It was just a black screen for 999 minutes.. and was a 1 hour recording..
I always us MGcamd 1.35a and ALWAYS use Vix..
ok report it on their website but I have no issues with recordings with new drivers so it is strange
Inviato dal mio GT-I9070 utilizzando Tapatalk
Also... I'm sorry but I'm italian and in Italy there is a provider that is not free so it is the reason why I asked u about softcam. Strange thing anyway, no problems here also on fta even if channels are on dvb-t or dvb-s and also on multiple recordings and providers and tuners...Trust me I testrd it for one week..
Inviato dal mio GT-I9070 utilizzando Tapatalk
are you recording to hdd in the box or to a NAS?
Vu Ultimo4K, OpenViX 5.0, 8xdvb-c, 8xdvb-s2, 2xdvb-t2
Vu Solo4K, OpenViX 5.0, 8xdvb-s2
Dreambox DM900, OpenViX 5.0, 2xdvb-s2, 2xdvb-c/t2
Terrestrial, Cable, Fixed 28.2e + Unicable2 LNB
Guys, i have the problem too now, i didn't have this problem with older drivers and i am recording on the same HDD as before.
So it has nothing to do with cam, or recording to a NAS or a HDD inside or external.
The problem simply didn't exist before, now it does.