Hi guys
flashed my technomate 500 super with gemini tm500 super dated 18/10/10 of this site but box is now stuck..when it turns on it is stuck on tv system wizard and wont work with remote control...any ideas
thanks
Hi guys
flashed my technomate 500 super with gemini tm500 super dated 18/10/10 of this site but box is now stuck..when it turns on it is stuck on tv system wizard and wont work with remote control...any ideas
thanks
Try re-flashing mate
All PM,s asking about c/s on cable will be ignored and reported to forum staff!
hi
wont let me connect with technomate control centre now..failed to connect please check your password and ip but i know these are correct..
You may need to use a RS232.
D I S C L A I M E R
My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!
Please help keep OpenViX online, donate HERE.
Rules can be found HERE
Support our sponsor World-Of-Satellite HERE
GIGABLUE UHD QUAD 4K, VU+ DUO 4K SE, ZGEMMA H7S, VU+ UNO 4K SE
Triax 1.1m Powered by TM2600, Fixed 28.2 Zone 2 dish with GT-SAT Unicable
Are you using Technomate_ControlCenter_7_1? Here is a tutorial to flash via serial lead
by digidude and the Technomate_ControlCenter_7_1 program
All PM,s asking about c/s on cable will be ignored and reported to forum staff!
Thanks bassethound
i will take box to my work pc in the morning which has serial port as my laptop dont have and i dont have adaptor either..i will report back later..
cheers
bassethound (26-10-10)
Hi Guys
i am at my pc at work now..i am getting around 15 of these messeges when i switch box on after opening file to download
e:invalid protocol 1 : ready 13.01.44
then have the following messege
e:unknown 13.01.44
any ideas
thanks
Are you using a null modem cable and have you checked you have the right com port set in Technomate_ControlCenter_7_1 in setup?
All PM,s asking about c/s on cable will be ignored and reported to forum staff!
If you know what the ip address is of the box then just open your browser and typ 192.16.......... and login to the box then flash a new image via the update option. (very similar to the dm800.)
Vu+Ultimo + Vu-Solo 1.1mtr Alloy dish + 60cm fixed, TM HH motor, hate footy LOVE motor-sport.
hi guys
i can access my box through pauls advice..anybody know the username and password for the gemini image??
much appreciated
password technomate..doh!! thanks guys
ok guys..i am in the enigma web interface..where to go now to flash my new image?..sorry for all the questions!!
First of all get the reciever all wired up before hitting the power make sure network cable is in...
open the front flap and hold your finger down on the power button then flick the power switch on at the back, KEEP YOUR FINGER HELD DOWN ON THE FRONT POWER BUTTON, keep it there until you see a number, now this number will be the end part of its ip address for example if it says 3 your ip address for the box will be 192.168.1.3 or obviously if your router has a different ip combination it will be the last digit of the ip address.
Now open up your internet browser on your pc and in the address bar just type out the IP address then click go this will then let you in to the technomate loading portal all you do is click browse which will be the location of the UR image you have downloaded find it and then double click, then click download, the image will now go in, once finished it will say done on the front panel just restart the machine..
YOUR STILL NOT DONE!!!!!
its very important you first do a factory reset
so press ok on english and then just exit out of the rest until you come to the enigma info bar press menu on remote goto setup, then expert setup, then factory reset...once restarted the box is then ready to go
TIP: blue x2 lets you to the blue panel download where you can get latest channel list etc>>>>>
HAVE FUN
(not my work, credits go to the author)
Last edited by paul362; 30-10-10 at 01:05.
Vu+Ultimo + Vu-Solo 1.1mtr Alloy dish + 60cm fixed, TM HH motor, hate footy LOVE motor-sport.
hi guys..just getting back to box tonite
am following pauls instructions..when i click on the image and click download all i get get on the miniweb page is checking but thats it...any ideas..sorry for all the questions!!!
D I S C L A I M E R
My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!
Please help keep OpenViX online, donate HERE.
Rules can be found HERE
Support our sponsor World-Of-Satellite HERE
GIGABLUE UHD QUAD 4K, VU+ DUO 4K SE, ZGEMMA H7S, VU+ UNO 4K SE
Triax 1.1m Powered by TM2600, Fixed 28.2 Zone 2 dish with GT-SAT Unicable