Welcome mate, glad your sorted.
Welcome mate, glad your sorted.
Support The Sponsor - Buy from the best HERE
Please abide by the rules - have a read HERE
VIX manual & guides >>HERE
Download images from >> HERE
New Box Setup Guide >>HERE
D I S C L A I M E R
My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!
PM HELP WILL BE IGNORED PLEASE POST HERE IN FORUM AS IT BENEFITS EVERYONE
Follow us on Twitter
NO CARD SHARING TALK WILL BE TOLERATED, LAN OR WAN! IN OPEN FORUM OR PM
IF THE POSTS HELP PLEASE CLICK THANKS OR ADD TO REP ?
Hi and thanks for a great new image!
I have an unusual fault and would appreciate any help... I cannot use web interface but it was working fine on V2.2.. if I type current static IP address of receiver I get "could not connect" error. I can FTP and TELNET into receiver fine. I also have no problem browsing the receiver through the network. I have also tried using ET9000CC but still same problem. Really can't understand what is happening here! Please help..
Please ignore earlier post.. have managed to log onto webif by putting :1601 at end of IP address. Not sure why this has changed as could just type IP address before.
HI .. I am about to upgrade to vix 2.3 image,, and i have a few questions !
Is it recommended to unplug my internal HDD before upgrade ?
Can i use backup fav channel list on the new image ?
What image are you currently using? if its VIX 2.3 155 or greater than go blue button>VIX.Backup manager and than backup your settings and it will allow you to restore on a flash but you wont need to do a new flash if on latest kernel release as you can do an update.
If your on the older kernel, you need to do a bootloader flash and than the image. You can use dreanboxedit to back up your settings and will need to also do your CFG file via FTP.
You do not need to unplug the HDD.
Support The Sponsor - Buy from the best HERE
Please abide by the rules - have a read HERE
VIX manual & guides >>HERE
Download images from >> HERE
New Box Setup Guide >>HERE
D I S C L A I M E R
My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!
PM HELP WILL BE IGNORED PLEASE POST HERE IN FORUM AS IT BENEFITS EVERYONE
Follow us on Twitter
NO CARD SHARING TALK WILL BE TOLERATED, LAN OR WAN! IN OPEN FORUM OR PM
IF THE POSTS HELP PLEASE CLICK THANKS OR ADD TO REP ?
i am using 2.2.110... so new bootloader and image......
and the only thing i would like to backup is the channel list ! Whats the smoothest way to do that ?
Help asked via PM will be ignored.
The forum is there for help and all will benefit from your questions.
NO CARD SHARING TALK WILL BE TOLERATED, LAN OR WAN, IN OPEN FORUM OR PM !
English is not my native tongue.
I apologise for all my grammar, spelling and idiom errors.
Use dreamboxedit, tutorial on how to do it in my signature. Its the same as sending to the box but last step is in reverse. You will need to specify a folder for the settings and I always create one on the desktop.
Support The Sponsor - Buy from the best HERE
Please abide by the rules - have a read HERE
VIX manual & guides >>HERE
Download images from >> HERE
New Box Setup Guide >>HERE
D I S C L A I M E R
My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!
PM HELP WILL BE IGNORED PLEASE POST HERE IN FORUM AS IT BENEFITS EVERYONE
Follow us on Twitter
NO CARD SHARING TALK WILL BE TOLERATED, LAN OR WAN! IN OPEN FORUM OR PM
IF THE POSTS HELP PLEASE CLICK THANKS OR ADD TO REP ?
Is there a guide for installing bootloader and image ?
Need to go here and download the BL and image.
http://www.world-of-satellite.com/sh...mage-Release-s
Make sure no other usb sticks connected and format the one you will be using to flash to FAT32
extract the BL and put the file called ET on the root and power down form rocker switch after shutting down and than power back up and click OK when asked.
Image flash is same as above but make sure you delete the BL folder
Support The Sponsor - Buy from the best HERE
Please abide by the rules - have a read HERE
VIX manual & guides >>HERE
Download images from >> HERE
New Box Setup Guide >>HERE
D I S C L A I M E R
My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!
PM HELP WILL BE IGNORED PLEASE POST HERE IN FORUM AS IT BENEFITS EVERYONE
Follow us on Twitter
NO CARD SHARING TALK WILL BE TOLERATED, LAN OR WAN! IN OPEN FORUM OR PM
IF THE POSTS HELP PLEASE CLICK THANKS OR ADD TO REP ?
Bootloader and image flash ok
But what about mgcamd..... can i use the same install package as i used with vix 2.2.110 ???
Support The Sponsor - Buy from the best HERE
Please abide by the rules - have a read HERE
VIX manual & guides >>HERE
Download images from >> HERE
New Box Setup Guide >>HERE
D I S C L A I M E R
My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!
PM HELP WILL BE IGNORED PLEASE POST HERE IN FORUM AS IT BENEFITS EVERYONE
Follow us on Twitter
NO CARD SHARING TALK WILL BE TOLERATED, LAN OR WAN! IN OPEN FORUM OR PM
IF THE POSTS HELP PLEASE CLICK THANKS OR ADD TO REP ?
works great....
but how can i make my own channel list !? ......
I Move Picons folder to a usb pendrive but the box will not read/find then from my usb pendrive :-( where i can edit the path?
And i also got this and my box crash :-(
[SKIN] Parsing embedded skin
[Skin] SKIN ERROR in screen '<embedded-in-'VIXMenu'>' widget 'widget': {PLi-HD/skin.xml}: source 'status' was not found in screen '<embedded-in-'VIXMenu'>
Any help?
Thx
Last edited by ovi; 16-02-12 at 19:59.
Hello', thanks for your great image.
I have returned to VIX after a period where I was using other images. VIX is always very nice and reliable!
bassethound (20-02-12),punisher (20-02-12),Rob van der Does (20-02-12),Sicilian (20-02-12)