encryption? no idea, it is an official Canaldigitaal card.
encryption? no idea, it is an official Canaldigitaal card.
You are not doing yourself posting all over the forums the same questions.
Keep this topic in the thread here http://www.vuplus-support.co.uk/show...stalling-CCcam If you post in anymore sections the same question I will delete them. Now please just keep your question in one thread so that we can keep track of what your are doing/trying.
D I S C L A I M E R
My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!
Please help keep OpenViX online, donate HERE.
Rules can be found HERE
Support our sponsor World-Of-Satellite HERE
GIGABLUE UHD QUAD 4K, VU+ DUO 4K SE, ZGEMMA H7S, VU+ UNO 4K SE
Triax 1.1m Powered by TM2600, Fixed 28.2 Zone 2 dish with GT-SAT Unicable
So far it is an improvement, but when it starts I get this staring woman and in the upper left corner it says:
"loading defaults...."
and the text "loading defaults...." never goes away. I think that is not good.
By the way, nowhere is explained what defaults are. What are defaults?? What is the purpose of this message?
Visiosat BIG Bisat / 3x inverto Ultra Quattro LNB /1x ALPS Quad / Astra 1,2,3 Hotbird / VUPLUS / 2xVUSOLO / Draytek Vigor2130n Gigabit router / Synology DS-109 NAS / Cat-6 cable
if its stuck on loading Defaults then press the ok button and check your AGC and SNR rates (presuming you have channels loaded already) if you have not loaded the files mentioned earlier by Sic you will have 0 and 99% in the signal because you need the new drivers for the tuner to work properly.
If on the other-hand you have not loaded the Default channels and have loaded the new drivers (as instructed by Sic) then just go ahead and download your chosen channel package either from the vti panel or use dream-set or your favorite programmer to send them over after this reboot and you should be up and running fine.
PS: loading Defaults just means the box is booting up as normal.
Vu+Ultimo + Vu-Solo 1.1mtr Alloy dish + 60cm fixed, TM HH motor, hate footy LOVE motor-sport.
Sicilian (22-08-10)
I have just flashed the solo with the latest vti image.
my sys config as follows
3 fixed sat connected to diseqc 4x1
sat1@diseqc 1 >>port A
sat2@diseqc 2 >>port B
sat3@diseqc 3 >>port C
solo config as follows
config mode=simple
mode=diseqc A/B/C/D
port A sat1
port B sat2
port C sat3
set voltg=yes
send diseqc =no
first time before drivers updated all 3 sats get no signal / always on 99%
but when i installed the drivers attached to the post (mbox-dvb-modules_2.6.18-7.3-r20-20100611_vusolo.zip). sat1@diseqc 1 >>port A + sat2@diseqc 2 >>port B work 100%.
but sat3@diseqc 3 >>port C get no signal / always on 99%
please need your help
BTW:
1- tested same sys config with others receivers (humax5400)and all 3 sats work 100%.
2- changed 4x1 switch still same .
Last edited by appc777; 22-08-10 at 11:59.
Can you test with the latest official image and report back please? http://www.vuplus-support.co.uk/show...mage-Ver.-5.1a
D I S C L A I M E R
My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!
Please help keep OpenViX online, donate HERE.
Rules can be found HERE
Support our sponsor World-Of-Satellite HERE
GIGABLUE UHD QUAD 4K, VU+ DUO 4K SE, ZGEMMA H7S, VU+ UNO 4K SE
Triax 1.1m Powered by TM2600, Fixed 28.2 Zone 2 dish with GT-SAT Unicable
I did all kind of swapping between cables on different ports after all theses tests I found out I can not connect more than 2 fixed satellites in different diseqc. Only 2 fixed satellites and the others no signal / always on 99%
BTW:1- tested same sys config with others receivers (humax5400)and all 3 sats work 100%.
I would email vuplus. Looks like you exhausted the possibilities and it could be a bug in the software. Send an email to: -
Code:alex@vuplus.com
Official Distributor of Formuler products, GiGaBlue, Octagon,
Technomate, Tiviar, VU+, Xtrend and many more...Secure online ordering - Paypal and all major cards accepted - Order online 7 days a week!PRICE MATCH PROMISE - WE'LL TRY TO MATCH ANY UK PRICE**SEEN ANY PRODUCT CHEAPER? CONTACT US AND WE’LL TRY TO MATCH LIKE FOR LIKE!
grtmoby (23-08-10)