Sorry no luck same issues
Thedoc
VU+ Duo 4K SE
Zone 2 dish 60cm
Gigablue LNB Unicable SCR 2 legacy 5.4 (release)
Positioned to 28.2E
@thedoc11
Please post a screenshot of a the following page on your Gigablue:
Menu > Information > Devices
Secondly, if you still have your Solo2, can you hook that up to the Unicable LNB, exactly as you did in your diagram. You will only be able to set tuner A & B. Do both these tuners work fine? Experiment with changing the preferred tuner, put box into standby, then wake up box. This will rule out the LNB.
There was another thread a while ago, a different LNB, but the cable tuner problem is also mentioned.....
https://www.world-of-satellite.com/s...ith-a-quad-LNB
Ok so it looks like my LNB is working correctly as my sony TV has the capability to utilise unicable and it is finding channels fine and working as it should do so that irons out the lab is that correct ?
i may try and re flash and not restore settings and try from scratch and see what happens will get back you in due course
Thedoc
VU+ Duo 4K SE
Zone 2 dish 60cm
Gigablue LNB Unicable SCR 2 legacy 5.4 (release)
Positioned to 28.2E
Last edited by Andy_Hazza; 04-01-21 at 20:27.
Thedoc
VU+ Duo 4K SE
Zone 2 dish 60cm
Gigablue LNB Unicable SCR 2 legacy 5.4 (release)
Positioned to 28.2E
abu baniaz (04-01-21)
I'm new to Unicable but would expect that if you have tried the Unicable cable feed directly from LNB (not the other legacy cable feeds) to your Sony TV and it worked then that would rule out that specific cable and F connector.
Have you tried Unicable cable from LNB directly to Gigablue box (without splitter) into Tuner A without setting up additional tuners and does this work, albeit limited on tuners that can be used? Also have you tried the same thing directly into Tuner B and not A and is that same?
Before you spend money on a call out charge...
Which dish is the LNB installed on?
Who installed the LNB?
Are you testing the same services to hit the error?
I presume you have the legacy ports still connected. Perform a manual scan, single satellite, (do not enable network scan). How many services do you find? Do not use plugins like ABM for this test.
bbbuk (05-01-21)
Legacy is still connected
manual scan I get 0 channels downloaded
ABM was not used
Am using a zone 2 60cm mesh dish
Installed by an approved installer
I took your advise not to get anyone out just yet,
1. i got on a ladder and clipped off the old connector, and put on a brand new compression fitting on.
2. Tested the system and i got exactly the same issue.
3. Clipped off the other end off the cable attached to the unicable and fitted a new compression fitting and attached this to the input of the power splitter
4. got some new shotgun cable and made a brand new cable up from the power pass splitter to the tuner
5. Connected one to the TUNER A and One to TUNER B
6. powered up the STB and the channels came on immediately.
7. placed the STB into standby for 5 mins and the Channels appeared immediately
8. Left the STB powered down for 15mins Approx and then powered up the Channels came on Immediately
Just tried to change the channels and am back at square one no channels not displaying again
Since writing the above all my channels are back again
Thedoc
VU+ Duo 4K SE
Zone 2 dish 60cm
Gigablue LNB Unicable SCR 2 legacy 5.4 (release)
Positioned to 28.2E
abu baniaz (06-01-21)
Checking/re-terminating the cables is a good start. Fault finding needs to be methodical and systematic and limit the variables. Can we leave out the unicable for time being and just use the legacy connections?
A screenshot of Menu > Information > Devices is still pending to remove the query about which tuner modules you have.
The services/channels being tested need to remain constant as far as possible.
Once you have the the legacy connections set hooked up and tuners configured correctly, can you please conduct the following two tests.
A manual scan, Tuner A, single satellite, No to network scan, should yield 880+ services.
A manual scan, Tuner B, single satellite, No to network scan, should yield 880+ services.
Last edited by abu baniaz; 08-01-21 at 19:39. Reason: Correct tuner letter error
Completed a full automatic scan and got 893 channels scanned
What I have noticed if I do a cold boot after a long period then boot I seems to have to wait for it to come back about 10mins or so not sure if this is normal I get a tune fail error will keep and Eye on this and report back team.
Thedoc
VU+ Duo 4K SE
Zone 2 dish 60cm
Gigablue LNB Unicable SCR 2 legacy 5.4 (release)
Positioned to 28.2E
abu baniaz (06-01-21)
Thanks for the screenshot. Whichever tuner was used in last scan is OK. Automatic scan has very little control. Please try manual scan. That way you can select tuner to use as well as type of scan.
As we are solely using Legacy connections now, the unicable tune failed/power issue is not part of the equation. On occasion, I find that a tune failed message that is latched is eradicated by selecting a service on Terrestrial then back to satellite. I haven't found a recipe/method to trigger it all the time, but there is a bug thread a a few years old with it.
Just out of curiosity, do you still have the solo 2 available? No need to do anything with it just yet.