well they're talking about in this thread if i'm not mistaken
well they're talking about in this thread if i'm not mistaken
...That's about Octagon drivers, nothing to do with SundTek.
ok, but it will create virtual tuners with the sundtek usb dvb-c tuner
No. I think you don't understand.
VTuner = USB tuner.Code:INFO: 4 x VTuner (USB) possible (4 x Virtual USB tuner possible)
So it means the Octagon drivers support up to four USB tuners.
But you only have one USB tuner.
It doesn't matter if the drivers support up to five billion tuners, if you only have one tuner installed that is all you can use.
New drivers again today.
Code:2017-07-12 -. CI slot bug fixed -. minor bugs fixed
bassethound (14-07-17),el bandido (13-07-17),Emulated (13-07-17),khan888 (12-07-17),Sicilian (12-07-17)
NEU: Treiber (Driver) update Octagon SF4008 - 13.09.17
[Release Note]
20170913
1. Tuner A - recording, tuner C live pixeling : fixed
2. ac3 no works. : fixed
3. Div. CI Module tested.
CI SETTING
dsmart & high bitrate ci modules:
menu->Setup->Common interface->Common interface-> set High bitrate support "yes"
If High bitrate support is set "No", pixeling will occur.
For all other CI Modules :
It does not matter high bitrate support is set Yes or No.
Users may choose a proper setting according to the circumstances.
5. Kernel patch for memory info on OSD to be shown 1GB
All PM,s asking about c/s on cable will be ignored and reported to forum staff!
Just replying to the above drivers, I,ve tried on two occaisions to update to Vix 5 0 0 27, from vix 26.
And on both occasions i,ve lost Audio and had to revert back to Vix26.
The method i used to update was through the sf4008 menu-softwareupdate.
Is anyone else having this problem ?
The last driver release mentioned is not in 5.0.027, but has a fix for "ac3 no works. : fixed".
yes i know, its when i update to 27 from 26. I lose audio.
Enigma 2 is not new to me, Having bought a number of box,s from the sponsor.
As soon as i try to update to Vix 27, I lose audio.
.....and the audio problem (AC3) is fixed in the next driver release, which is not in 027.
When drivers change or any anything "major" I would always flash the image and restore backup settings. I personally would not software update (although I realise I am probably in a minority of 1) and because of that view I never software update.
Might not stop your issue, but a new flash is worth trying
... although just read on another forum similar posts ref audio, so perhaps 2 steps forward by Octagon and 1 step back?
Last edited by twol; 14-09-17 at 11:54.
Gigablue Quad 4K & UE 4K
.........FBC Tuners:
------------------> GT-Sat unicable LNB to 1.5M dish(28.2E)
------------------> Gigablue unicable LNB to 80 cm dish(19.2E)
.......................
Vu+ Uno4KSE, Dreambox dm900
AX HD61, Edision Osmio 4K+, Zgemma H9Combo, Octagon SF8008 , gbtrio4k, h9se using unicable ports
Zgemma H9 C/S into Giga4K
Sf4008 drivers updated on the OE-A fixing AC3 issue ..... in next OpenViX build ......
Gigablue Quad 4K & UE 4K
.........FBC Tuners:
------------------> GT-Sat unicable LNB to 1.5M dish(28.2E)
------------------> Gigablue unicable LNB to 80 cm dish(19.2E)
.......................
Vu+ Uno4KSE, Dreambox dm900
AX HD61, Edision Osmio 4K+, Zgemma H9Combo, Octagon SF8008 , gbtrio4k, h9se using unicable ports
Zgemma H9 C/S into Giga4K
el bandido (20-09-17)