Just got a Nano 2 super through the door. Plugged it all in - green light on, flashes for a bit - no output to TV though. Any ideas? Tried different HDMI leads, sockets and TV's.
Agghhhhhhh this is so annoying!!!
Just got a Nano 2 super through the door. Plugged it all in - green light on, flashes for a bit - no output to TV though. Any ideas? Tried different HDMI leads, sockets and TV's.
Agghhhhhhh this is so annoying!!!
Should have purchased from us, we would have pre-flash and boot tested prior to shipping
Official Distributor of Formuler products, GiGaBlue, Octagon,
Technomate, Tiviar, VU+, Xtrend and many more...Secure online ordering - Paypal and all major cards accepted - Order online 7 days a week!PRICE MATCH PROMISE - WE'LL TRY TO MATCH ANY UK PRICE**SEEN ANY PRODUCT CHEAPER? CONTACT US AND WE’LL TRY TO MATCH LIKE FOR LIKE!
D I S C L A I M E R
My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!
Please help keep OpenViX online, donate HERE.
Rules can be found HERE
Support our sponsor World-Of-Satellite HERE
GIGABLUE UHD QUAD 4K, VU+ DUO 4K SE, ZGEMMA H7S, VU+ UNO 4K SE
Triax 1.1m Powered by TM2600, Fixed 28.2 Zone 2 dish with GT-SAT Unicable
I know WOS, but my mate has his own aerial co so was trying to support him a little - even cost me a bit more than you guys!
Sicilian - not done a thing. It's fresh out of the box
Try flashing a image and are you sure it's a genuine receiver and not a clone.
Sent from my SM-G900F using Tapatalk
My posts contain my own personal thoughts and opinions, they do not represent those of any organisation or group but my own.
If you don't like what I post, Don't read it.
SIMPLES.
Its genuine for sure.
Works on yellow plug output just not HDMI - Any ideas? Bad HDMI port? Turned box off and plugged in both HDMI and yellow plug and it worked. As soon as I pulled the yellow plug it lost pic.
What image is on there now? As much detail as possible
Menu > Information > About
when you say the yellow plug is that the phono video as with the red and white,if it has a picture with the yellow plug in check settings are not setup like scart as it might stop hdmi working and change to hdmi setting??
OpenPli 3.0
Says powered by 4d
Cactikid - only options I could find were HDMI or HDMI PC. The set up wizard did the usual 'can you see this screen' thing and didn't cycle through anything other than HDMI option too, even though it was the yellow (yes the type you are thinking of) plugged in
Start afresh.
Flash the latest 4D image
Code:http://downloadtmsw.com/bbs/list.php?board=tmnano2super
or Vix image
http://openvix.co.uk/index.php?dir=TM-Nano2-Super
Guide to flashing
http://openvix.co.uk/index.php?dir=G...hing%20Guides/
I have a new box coming weds (spoke to my supplier and he will order it tomorrow). If I put Vix on it, and it still doesn't work, will the factory reset option put it back to openpli 4d?
Also make sure that the hdmi cable is inserted fully.
It's deffo in all the way! Shall I go ahead and flash? I need to know a factory reset will put openpli back on it
Installing an image clears everything. You will have to flash the 4D image if you want that back on.
Sponsor does a good deal and £5 discount on the Nano 3T.