Smargo

[canthackit]

Hello

i've not used a smargo for some years, used it on a DB800 i want to test it out on my 9000, but i've forgot the serial reader line, i have read some postings on the subject but i'm still not lucid on the subject so is the serial reader line tts? or tty? ie SERIAL READER : /dev/usb/tty/0 smartreader+.........and here's the dumbo question chip up or down, i've tried both ways and it's not working at all.

regards: canthackit

[Sicilian]

Post 13 here http://www.world-of-satellite.com/sh...ghlight=smargo

Chip up I believe.

[canthackit]

Thanks Boss

and that was your posting i went to, so i had the chip the right way round "up"

and this is the line i have now: SERIAL READER : /dev/ttyUSB0 smartreader+

rebooted and restarted the cam

and still nothing clearing...................anything else i can try?

i'm sure all my other settings are ok boxkey etc and i always over clock my card to 5.5 Mhz and if i remember correctly it worked reall well in the 800

thanks & regards: canthackit

[Sicilian]

Double check your cfg.

[canthackit]

ok Boss

shame on you you told me wrong it's chip down i thought it was chip up as well though.

must say just as i had hoped the ecm times are significantly faster

so just to reiterrate it's:
SERIAL READER : /dev/ttyUSB0 smartreader+
chip down.

thanks and regards: canthackit

[pooface]

By significantly, how significantly?! From around 0.400? Or were they higher/lower?

Sent with Tapatalk

[canthackit]

Hello PF

on the internal readers i was getting round about .247ms
on the smargo i'm getting round about .150ms

then again the readers on my Vu+ are very low, low 100's 102, 103

regards: canthackit

[pooface]

Hello PF

on the internal readers i was getting round about .247ms
on the smargo i'm getting round about .150ms

then again the readers on my Vu+ are very low, low 100's 102, 103

regards: canthackit

I would suggest trying oscam/cccam combo, as oscam gives good ecm times, in cases <0.100 ... Saying that, even with around 0.250, you shouldn't be getting any problems...

Sent with Tapatalk

[canthackit]

oscam i find to difficult

got another problem now i cannot clear any HD movie channels, and quite a few of others as well, i know that this has been a problem in the past but i forget how to resolve it

any ideas please?

regards: canthackit

[canthackit]

not getting anywhere with this problem

do i need to change the boxkey file path for the smargo? at present it's still on /dev/sci0 do i need to change it to point to the smargo?

regards: canthackit

[Stanman]

not getting anywhere with this problem

do i need to change the boxkey file path for the smargo? at present it's still on /dev/sci0 do i need to change it to point to the smargo?

regards: canthackit

Yes, otherwise it wont have a boxkey, hence black screen

[olerocker]

Hey guys a little help would be deeply appreciated.
I have got a sly white card in my et9000 which works pretty good in a smargo reader with oscam that is till i reboot my box then it wont initialize my card to start decoding.
If i use the internal readers all works fine. I would prefer the smargo though.
Any help would be great,Thanks.

[canthackit]

Yes, otherwise it wont have a boxkey, hence black screen

see mate the obvious is not always obvious to me

thanks.

canthackit

[pooface]

see mate the obvious is not always obvious to me

thanks.

canthackit

It was, as u even suggested it

A leap of faith might help in the future (until it balls it up really bad, then I get the blame for suggesting u try doing it by urself )

Sent with Tapatalk

[pooface]

Hey guys a little help would be deeply appreciated.
I have got a sly white card in my et9000 which works pretty good in a smargo reader with oscam that is till i reboot my box then it wont initialize my card to start decoding.
If i use the internal readers all works fine. I would prefer the smargo though.
Any help would be great,Thanks.

How do u get it reading the smargo before it restarts and doesn't initialise the card?

What image are u using?

Are u using cccam/oscam? Does cccam take control of the card before oscam can? (Would happen if cccam starts before oscam)

Sent with Tapatalk