Blinscan in ViX Team Image
Hi everyone,
I have just released my review of the VU+ Uno and I used the ViX Team Image after briefly testing the stock firmware.Code:http://linux-tv.com/vu-uno-review
Is the blindscan included in the ViX Team Image and if so where do I find it?
Thanks in advance.
Last edited by Larry-G; 27-07-11 at 20:30. Reason: coded live link.
bassethound (27-07-11)
That's a very nicely put together article. at present i dont believe VIX has enabled the blind scan feature for the Uno ( or at least like you i could not find it on my Uno )
Last edited by Larry-G; 27-07-11 at 20:44. Reason: typo
My posts contain my own personal thoughts and opinions, they do not represent those of any organisation or group but my own.
If you don't like what I post, Don't read it.
SIMPLES.
Very nice review of the uno
blind scan on the et5000/et9000 is in service search/manual scan/then toggle through type of scan till you find blind scan
All PM,s asking about c/s on cable will be ignored and reported to forum staff!
nope it's not there on with VIX on the Uno running the latest beta image, only gives options for single transponder / single satellite and multisat. no options for blindscan.Originally Posted by bassethound
Very nice review of the uno
blind scan on the et5000/et9000 is in service search/manual scan/then toggle through type of scan till you find blind scan
My posts contain my own personal thoughts and opinions, they do not represent those of any organisation or group but my own.
If you don't like what I post, Don't read it.
SIMPLES.
Has blind scan been activated on the uno yet? I know the tuners are capable, but not seen anything about it beong activated (but likely missed it
Sent with Tapatalk
i believe its active in the official image, i'll test it this afternoon when i get up ( just got in from work ).
My posts contain my own personal thoughts and opinions, they do not represent those of any organisation or group but my own.
If you don't like what I post, Don't read it.
SIMPLES.
bassethound (28-07-11)
ok just had a quick look at the offitial Vu+Uno image and yes as the op stated blindscan is activated within this image under menu>plugins.
here is a very quick set of scans i just performed using the blindscan feature on the Uno with the offitial Image.
location 28.2 east
scan start freq 0950000000
scan stop freq 2150000000
polarity Horizontal
scan band low
scan start symbolrate 0002000000
scan stop symbolrate 0045000000
total scan time 1 minute 21 seconds
329 services found
========================
location 28.2 east
scan start freq 0950000000
scan stop freq 2150000000
polarity Horizontal
scan band high
scan start symbolrate 0002000000
scan stop symbolrate 0045000000
total scan time 1 minute 33 seconds
317 services found
==========================
location 28.2 east
scan start freq 0950000000
scan stop freq 2150000000
polarity Vertical
scan band low
scan start symbolrate 0002000000
scan stop symbolrate 0045000000
total scan time 1 minute 39 seconds
250 services found
===========================
location 28.2 east
scan start freq 0950000000
scan stop freq 2150000000
polarity Vertical
scan band high
scan start symbolrate 0002000000
scan stop symbolrate 0045000000
total scan time 1 minute 48 seconds
291 services found.
============================
My posts contain my own personal thoughts and opinions, they do not represent those of any organisation or group but my own.
If you don't like what I post, Don't read it.
SIMPLES.
bassethound (28-07-11),pooface (28-07-11)
Is there any way to get it to perform all those scans in one run?
Also, you are doing an overlap in that scan so it could do it even faster and still cover all frequencies. Not that it matters as it will only store one copy of the channels in the overlap. Correct settings would be 950 - 1950 in low band, and 1100 - 2150 in high band.
@Linux-TV, what did it mean in the review that blind scan hasn't been optimised yet?
Last edited by Huevos; 28-07-11 at 22:23.
Posting Permissions
Reply With Quote
