No automatic boot after flashing online

[skippie]

ok set to local time

[abu baniaz]

My Duo 4K as been doing the same/similar thing too, it gets stuck on the Vu+ logo, so before E2 as started as far as I know. It is on PLI nightly developer builds and did it when I was using ViX on it. Even deep standby is an issue and you have to reflash to get out of it. Flash by USB or Ofgwrite does not matter.

Console log is attached. Small excerpt below

INIT: version 2.88 booting


Fuse filesystem already available.
Mounting fuse control filesystem.
Starting udev
[    3.278339] udevd[790]: starting version 3.2.8
[    3.292888] random: udevd urandom read with 24 bits of entropy available
[    3.313248] udevd[791]: starting eudev-3.2.8
[    3.657192] usb 1-2: new high-speed USB device number 2 using xhci-brcm
[    3.777407] EXT4-fs (sda1): recovery complete
[    3.781814] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[    3.789726] hub 1-2:1.0: USB hub found
[    3.793545] hub 1-2:1.0: 4 ports detected
[    3.900185] usb 1-1: new high-speed USB device number 3 using xhci-brcm
[    4.020840] hub 1-1:1.0: USB hub found
[    4.024666] hub 1-1:1.0: 4 ports detected
[    5.072180] usb 1-2.4: new full-speed USB device number 4 using xhci-brcm
[    5.241177] usb 1-2.3: new high-speed USB device number 5 using xhci-brcm
[    5.347537] EXT4-fs (mmcblk0p9): re-mounted. Opts: (null)
grep: /sys/devices/platform/Fixed: No such file or directory
grep: MDIO: No such file or directory
grep: bus.0/modalias: No such file or directory
/etc/rcS.d/S21bootlogo: line 4: /proc/stb/video/videomode: No such file or directory
/dev/dvb/adapter0/video0: No such file or directory
vm.dirty_writeback_centisecs = 300
vm.dirty_background_ratio = 1
vm.dirty_ratio = 60
ALSA: Restoring mixer settings...
/usr/sbin/alsactl: load_state:1735: No soundcards found...
wifi found
Vendor 0x1d6b ID 0x3
Vendor 0xa5c ID 0xbd27
usb_set_debug: Setting debugging level to 255 (on)
claiming interface 0
Found device: vend=0xa5c prod=0xbd27
File Length: 572654
ID : Chip 0xaa31 Rev 0x2RamSize 786432 RemapBase 0x00180800 BoardType 0 BoardRev 0
start
[    8.853086] random: nonblocking pool is initialized

[skippie]

So there's no solution to my problem i suppose ?

[ccs]

None of your debug logs include references to [OnlineUpdateCheck] or [ImageManager].

Do you only reboot the box when attempting to update it?

My Ultimo4K is left in deep standby overnight, and I've used Imagemanager to couch flash hundreds of times without any problems.

[skippie]

I think it's obvious that there isn't gonna be a log when i have to hard reboot because the box doesn't reboot by itself anymore. So i don't know what's going wrong.

Once more :

1. after an update the box doesn't reboot, i have to hard boot.
2. after an online flash install, same problem, i have to hard boot.
3. after a normal reboot command, the box doesn't want to reboot automatically, again i have to hard boot.

In short : i always have to reach to the button at the back of the box to hard reboot.

[ccs]

There will be debug logs if you change their location to /media/hdd/logs.

[twol]

I think it's obvious that there isn't gonna be a log when i have to hard reboot because the box doesn't reboot by itself anymore. So i don't know what's going wrong.

Once more :

1. after an update the box doesn't reboot, i have to hard boot.
2. after an online flash install, same problem, i have to hard boot.
3. after a normal reboot command, the box doesn't want to reboot automatically, again i have to hard boot.

Providing you have turned on debug logs and you have on hdd or usb not flash … there will logs showing activities.
Next time it stops try using filezilla to,access the current log and copy,it to a PC, so,it can be looked at.

[skippie]

Ok got 5 logs here, maybe something's coming up in there. Have been hard booting certainly within these logdates.

[ccs]

References in the logs to multibooting, which the ultimo4k doesn't have. Are you running a plugin to do this?

EDIT: my Ultimo4k also has similar references.

10:57:59.0976 [Console] command: mount /dev/mmcblk0p1 /tmp/getMultibootslotsz0n8tz1i
10:57:59.0978 [eConsoleAppContainer] Starting /bin/sh
10:57:59.0983 [Console] pid = 31331
10:57:59.1957 [multiboot] [getMultibootslots] Finished bootslots = {}
10:57:59.1958 [Console] command: umount /tmp/getMultibootslotsz0n8tz1i
10:57:59.1959 [eConsoleAppContainer] Starting /bin/sh
10:57:59.1964 [Console] pid = 31371
10:57:59.2064 [Console] command: mount /dev/mmcblk0p3 /tmp/getMultibootslotsz0n8tz1i
10:57:59.2065 [eConsoleAppContainer] Starting /bin/sh
10:57:59.2069 [Console] pid = 31372
10:57:59.2845 [multiboot] [getMultibootslots] Finished bootslots = {}
10:57:59.2846 [Console] command: umount /tmp/getMultibootslotsz0n8tz1i
10:57:59.2847 [eConsoleAppContainer] Starting /bin/sh
10:57:59.2851 [Console] pid = 31413
10:57:59.2947 [Console] command: mount /dev/mmcblk0p4 /tmp/getMultibootslotsz0n8tz1i
10:57:59.2948 [eConsoleAppContainer] Starting /bin/sh
10:57:59.2952 [Console] pid = 31414
10:57:59.3046 [multiboot] [getMultibootslots] Finished bootslots = {}
10:57:59.3047 [Console] command: umount /tmp/getMultibootslotsz0n8tz1i
10:57:59.3048 [eConsoleAppContainer] Starting /bin/sh
10:57:59.3052 [Console] pid = 31415
10:57:59.3207 [Misc_Options] 12Vdetect cannot open /proc/stb/misc/12V_output: Function not implemented
10:57:59.3327 [Harddisk] Enumerating block devices...
10:57:59.3493 [Harddisk] len partitions = 1, device = sda
10:57:59.3494 [Harddisk] Found storage device 'sda' (Removable=False) NoPartitions = 1.
10:57:59.3506 [Harddisk] Command: 'hdparm -S0 /dev/sda'.

/dev/sda:
setting standby to 0

[skippie]

No i never used multibooting.

[twol]

You have a Motorised dish and one of the logs shows a tuning failure at the end of the log ……. So maybe hanging on the motorised dish
How are your tuners setup… can you post pictures? … and perhaps describe your sat setup

[skippie]

No, i have a dish with 4 LNB's (13E-19.2E-23.5E-28.2E).

[twol]

No, i have a dish with 4 LNB's (13E-19.2E-23.5E-28.2E).

So you need to post information about the setup, diseqc commands are being issued, so would like to understand more.

[skippie]

1 dish with 4 LNB and 2 diseq switch boxes 4 in x 2 out each.

[skippie]

Strangely, as of yesterday (still on 6.00.8) my receiver booted again on his own without me switching off and on again at the back. Only thing that changed is that i replaced my broken external HDD with a new one of 2 TB. Could it be that HDD then preventing from booting properly ??? But my problem got fixed finally. Thnx for all those trying to help me. Cheers guys. Updated to the latest image yesterday evening with flashing online and the receiver booted up properly afterwards, i'm a happy man.