Hello, is there somewhere a setting that at power failure the box will boot to standby ? At OpenPLi the setting can be found from Main menu/Setup/System/Customize/
Hello, is there somewhere a setting that at power failure the box will boot to standby ? At OpenPLi the setting can be found from Main menu/Setup/System/Customize/
Is there enigma2-plugin-extensions-startuptostandby available, because the setting is missing.
Answering to myself : enigma2-plugin-extensions-startuptostandby_experimental-git20120501-r0_all.ipk is working with OpenViX. Case closed !
dntaylor (31-01-21)
Thanks for that....I was wondering it their was an extension for this.
..... I thought power timers would be the solution?
I never need use them, but find the interface to set them up impossible to understand.
I found the opposite about setting them up and find them useful. I only have three:-
i) to put my box into standby at 00:30 (am)
aaa.png
ii) to put my box into standby if I don't press a button on the remote for 2 hours
bbb.png
iii) to put my box into deep standby if it has been in standby for 10 minutes.
ccc.png
All power timers give an on-screen warning allow them to be manually over-ridden and or the timers are delayed if a recording is taking place (or about to take place)
The power timers work in conjunction so that, say, I walk away from my box and it is still on. After 2 hours the box will detect that I haven’t pressed a button on the remote and put up a warning that the box will go into standby in two minutes (with the options of manually cancelling the action). After two minutes the box goes to standby and the third power timer above kicks in – it waits 10 minutes and then puts my box into deep standby (or waits until a recording has finished).
I have a 10 minute wait until the box goes into deep standby just in case I’m pre-occupied when the standby warning comes up and I miss it. A box just going to standby can be restarted within a few seconds but a box going into deep standby the restart time is 2+ minutes. The box has to first completely close down to deep standby and then switch on again from the deep standby state.
Xtrend ET10K, 2 x satellite tuners 28.2 (Sky FTA), 2 x hybrid (UK Freeview), Zgemma H9S (satellite)
...thanks, it's a lot clearer when there's a description of what it actually does.
I still reckon starting from scratch without the finer detail is confusing, but I've never needed them, so never worked out what they could do..
Possible gotcha to watch out for.....
I was messing around with the time settings the other day and set it to hh.mm.ss in
menu → setup → time → time style
This gives a 12 hour clock display/format
When I went into my power timer in order to provide a screen shot the start date changed to 1st Feb and my time setting of 00:30 (30 minutes past midnight) changed to 12:30.
It is now impossible to set a time of 00:30 because that doesn’t exist on a 12 hour format clock, plus this timer would kick in twice a day at 12:30 am and 12:30 pm
The time format has to be changed to HH.mm.ss in “menu → setup → time → time style” in order to give a 24 hour clock format and allow the setting to be changed to 00:30 and which is only triggered once per day.
My now reconfigured timer.
ddd.png
The deep standby power timer also allows the box to go to that state when the power button is pressed once. Actually pressing the power button once puts the box into standby but the power timer then kicks in and 10 minutes later automatically puts the box into deep standby.
Last edited by adm; 31-01-21 at 15:23.
Xtrend ET10K, 2 x satellite tuners 28.2 (Sky FTA), 2 x hybrid (UK Freeview), Zgemma H9S (satellite)
LbCwby (23-05-21)
I was going to query your time setting as it looked like 12.30pm instead of 12.30am! I tend to use the 24 hour clock as I didn't like the way am/pm was displayed on various skins.
GB Quad Plus, Mut@nt HD51, AX HD61, 80cm dish and Supreme Dark motor. Sony STR-DN 1060, Sony UHP-H1 Bluray, Odroid N2+ (CoreElec), Monitor Audio Bronze 5.1 speakers
Yes, I use 24 hr format but the other day someone was questioning an incorrect time format message in the weather plug-in - as it worked for me, as a test I tried setting all time formats and inadvertently left it in 12 hour format. I did notice that some DATE and TIME formats didn't quite match what was being displayed in the skin.
Xtrend ET10K, 2 x satellite tuners 28.2 (Sky FTA), 2 x hybrid (UK Freeview), Zgemma H9S (satellite)
Joe_90 (31-01-21)
Joe_90 (01-02-21)
Found the plugin and installed and works fine. How can I edit the plugin so that box goes to deep standby??
CRMS (21-05-21)