I am going to try and help you.
Please only do what is asked of you. Do not try and do anything else.
Answer only what is asked of you. Do not add anything in your response that will confuse/complicate the issue
If questions/instructions are not clear, say so, instead of doing something else.
Are these conditions acceptable?
1. Please do not think about scanning at all. DO NOT GO anywhere into service searching menu
2.
Stop your receiver with the following command
Guide here if you need itCode:init 4
http://www.world-of-satellite.com/sh...Linux-commands
Do not proceed until you have done the step above
3.
Download and extract the attachment
4.
Transfer the attachments to /etc/enigma2
5.
Restart receiver with following command
6. select a service on 28.2: Press following on remoteCode:init 3
Channel Up
Green (satellite)
Highlight 28.2 and press OK,
Select any service you want
7.select a service on 19.2: Press following on remote
Channel Up
Green (satellite)
Highlight 19.2 and press OK,
Select ZDF (go upwards)
Questions: ( please answer with yes/no)
6A: Does motor move at all
6B: Do you get a lock on channels on 28.2
7A: Does motor move at all
7B: Do you get a lock on ZDF on 19.2
I'm at your instruction note 6. After entering init 3, the receiver restarted and is now saying please wait. Its been a few minutes like that.
ok had to click on menu to see if I can stake this any futher selected 28.2 and can see all channels.
Questions: ( please answer with yes/no)
6A: Does motor move at all - NO
6B: Do you get a lock on channels on 28.2 - YES
7A: Does motor move at all - NO
7B: Do you get a lock on ZDF on 19.2 - NO
Last edited by ALIEN1X; 25-04-17 at 19:18.
What happens if you press channel up on remote?
Or even TV?
Question 7C
When you attempt to select a 19.2 service, what happens on the screen.
Can you attach your settings file again please.
Please post answer in new post, instead of editing existing responses.
while on 28.2 I can press channel up on remote and go onto difrent channels.
I can move dish to 19.2 and select channels normally
I can only move dish if going into positioner settings and select move east or west
my settings.rarWhen I select 19.2 dish will not move, get blank screen. I have attached my settings file
typo error on post 24, should read - I can not move dish to 19.2 and select channels normally
Last edited by ALIEN1X; 25-04-17 at 19:36. Reason: attachement
Do you get an icon to indicate that it is trying to move?
Is dish visible from where you are?
Which image are you on?
I get icon dish is trying to move 28.2 to 19.2 but dish is not moving
dish is visible from where I am
when I select the channel on 19.2 even if dish will not move, it says Tune Failed.
selecting 28.2 back again its all ok on that sat only
my imgage is 5.0.0.11
Last edited by ALIEN1X; 25-04-17 at 19:52. Reason: typo
abu baniaz (25-04-17)
If you get an icon to indicate that it is trying to move, the software is fine. But that does not explain why you can move it in service searching menu manually.
Is the f-plug/wire direct to receiver or do you have any joints/face plates?
I have a cable between receiver and wall faceplate socket
from wall faceplate socket there is cable direct to motor.
The motor only moves east or west when I select positioner settings on reviver menu.
all the cables have f plugs
I can take a picture of my saterlight dish and motor if that helps?
my suspicion is on face plate. Can you bypass it using a joining barrell?