Hello Guest, if you are reading this it means you have not registered yet. Please take a second, Click here to register, and in a few simple steps you will be able to enjoy our community and use our OpenViX support section.
Results 1 to 7 of 7

Thread: CrashLogs for ET8500

  1. #1
    Mr. Mister's Avatar
    Title
    Moderator
    Donated Member
    Join Date
    Jul 2010
    Location
    Northern Ireland
    Posts
    4,936
    Thanks
    4,825
    Thanked 2,677 Times in 1,190 Posts

    CrashLogs for ET8500

    Further to this conversations on ET8500..

    http://www.world-of-satellite.com/sh...500-bootloader

    I attach the below crashlogs..

    Any help please guys.. ?
    Attached Files Attached Files

  2. #2
    twol's Avatar
    Title
    Moderator
    Join Date
    Apr 2012
    Posts
    8,422
    Thanks
    997
    Thanked 2,894 Times in 2,247 Posts
    To be clear: is this before or after a bootloader flash?
    Also what are you doing with the remote prior to the crash? Shows keys pushed in log?
    I assune the Lcd is up and running?
    Running on Vix 4.2 should not be an issue, at least runs on mine without issue.
    I would be tempted to remove the casing via the 2 nuts and reseat the tuners (although it recognises them) and eject any hdd for starters.
    Gigablue Quad 4K & UE 4K
    .........FBC Tuners:
    ------------------> GT-Sat unicable LNB to 1.5M dish(28.2E)
    ------------------> Gigablue unicable LNB to 80 cm dish(19.2E)
    .......................> FBC & DVB-S2X into 90cm dish (27.5W) Opticum robust Unicable LNB
    AX HD61, Edision Osmio 4K+, Zgemma H9Combo, Octagon SF8008 , gbtrio4k, h9se using unicable ports
    Zgemma H9 C/S into Giga4K

  3. The Following User Says Thank You to twol For This Useful Post:

    Mr. Mister (16-08-16)

  4. #3
    Mr. Mister's Avatar
    Title
    Moderator
    Donated Member
    Join Date
    Jul 2010
    Location
    Northern Ireland
    Posts
    4,936
    Thanks
    4,825
    Thanked 2,677 Times in 1,190 Posts
    Cheers twol for the reply.. b

    This is after the bootloader flashed.. ( But was doing the same thing before i flashed the the singleboot bootloader..
    Remote sitting on the coffe table not being touched..
    LCD is as default.. I have not got that far to change anything..

  5. #4
    twol's Avatar
    Title
    Moderator
    Join Date
    Apr 2012
    Posts
    8,422
    Thanks
    997
    Thanked 2,894 Times in 2,247 Posts
    So not as far as wizard?
    Gigablue Quad 4K & UE 4K
    .........FBC Tuners:
    ------------------> GT-Sat unicable LNB to 1.5M dish(28.2E)
    ------------------> Gigablue unicable LNB to 80 cm dish(19.2E)
    .......................> FBC & DVB-S2X into 90cm dish (27.5W) Opticum robust Unicable LNB
    AX HD61, Edision Osmio 4K+, Zgemma H9Combo, Octagon SF8008 , gbtrio4k, h9se using unicable ports
    Zgemma H9 C/S into Giga4K

  6. #5
    Mr. Mister's Avatar
    Title
    Moderator
    Donated Member
    Join Date
    Jul 2010
    Location
    Northern Ireland
    Posts
    4,936
    Thanks
    4,825
    Thanked 2,677 Times in 1,190 Posts
    Yes.. I went through FIW
    Then done a fresat scan.. and put it on BBC Olympic 2HD
    Watching the cycling.. All was good for 30 mins.. Then crashed.. Usually crashed after 10 mins before i flashed the bootloader..
    After above.. I installed cam via ftp..
    No picons added..
    Done a full ABM scan on 28e..
    mounted the HDD
    EPG went in fine for the 1st time after fresh flash.. Usually locked up on 4.80mb .. Although it was seriously slow.. about 10 mins.. Usually takes 90 secs on Quad+..
    So just went back to BBC Olympic 2HD.. and after approx 20 mins.. another crash.. Logs attached above..
    Remote never touched after channel selection..

  7. #6
    Mr. Mister's Avatar
    Title
    Moderator
    Donated Member
    Join Date
    Jul 2010
    Location
    Northern Ireland
    Posts
    4,936
    Thanks
    4,825
    Thanked 2,677 Times in 1,190 Posts
    3 more crash logs in 40 mins.. And its in a room under lock and key.. No one can get it to..
    Attached Files Attached Files

  8. #7
    twol's Avatar
    Title
    Moderator
    Join Date
    Apr 2012
    Posts
    8,422
    Thanks
    997
    Thanked 2,894 Times in 2,247 Posts
    So before it crashes can you 1)turn on debug logs
    Then go into standby, delete epg.dat from flash/hdd and where ever and pwr off/on
    Then lets see what the debug shows .... if any other than program check
    Just trying to think of anything that might help .... I have beat the ***** out of my office machine, run it at very high temperatures and its been fine (cross fingers) .

    And Yes Crossepg takeslonger on all Xtrend receivers than Vu+ although about 5 minutes for mine on UK epg.
    Last edited by twol; 16-08-16 at 17:02.
    Gigablue Quad 4K & UE 4K
    .........FBC Tuners:
    ------------------> GT-Sat unicable LNB to 1.5M dish(28.2E)
    ------------------> Gigablue unicable LNB to 80 cm dish(19.2E)
    .......................> FBC & DVB-S2X into 90cm dish (27.5W) Opticum robust Unicable LNB
    AX HD61, Edision Osmio 4K+, Zgemma H9Combo, Octagon SF8008 , gbtrio4k, h9se using unicable ports
    Zgemma H9 C/S into Giga4K

  9. The Following 2 Users Say Thank You to twol For This Useful Post:

    Bangord30 (16-08-16),Mr. Mister (16-08-16)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
This website uses cookies
We use cookies to store session information to facilitate remembering your login information, to allow you to save website preferences, to personalise content and ads, to provide social media features and to analyse our traffic. We also share information about your use of our site with our social media, advertising and analytics partners.