et 10000

[casuk]

hi, iv just got an xtrend et 10000 and im trying to set it up but ABM just says timed out for tuner lock, iv managed tos scan over 600 channels and while looking in all channels I can find the cable channels but just a blank screen, but bbc one wales worked, but not bbc one Scotland, do I need dvbsnop or lamedb, also should I flash bootloaded

[abu baniaz]

Bootloaders are only required when manufacturers provide them.

Your thread should really be in teh ABM support section as your issue is ABM. I'll move it later. Please upload the debug log as per this thread: http://www.world-of-satellite.com/sh...port-questions

How many tuners?
Do they all have cables/wires?

[casuk]

It not ABM I can scan sat and scan USB cable tuner its something else, if i disconnect the cables from tuners and just run the USB tuner all works and if I connect the cables back up and disconnect the USB it still works

[casuk]

I have 3 cable tuners installed, and one sat, sat is fine its just the cable side in having trouble with, if I scan ABM with just cable USB tuner I find all the channels but I get tune failed if I try watch one, but if i connect the cables to the built in tuner I get picture working but no ABM just times out

[abu baniaz]

Do you have cables connected to all three DVB-C tuners?

Are you certain that you are using the correct Net-ID?

[casuk]

Enigma2-01-01-1970_01-00-19.log
yes glasgow 00002 im setting up as iv always done same way no diffrence

[abu baniaz]

ABM uses the last tuner for the type of service as this is likely to be not in use, this is why I asked if all tuners had a cable connected. If all tuners have cables connected, you need to boost your signal.

[casuk]

Iv got a booster, i can also run 4 cable tuners with no problems at all, everything was fine on my gigablue last week nothing has changed cable wise, I'm lost about what to do I even tryed another image (ATV latest) same thing

[abu baniaz]

Does your ET1000 have cables connected to all DVB-C tuners? I am asking about what it has, not what it can have.

[Huevos]

Please post the debug log of a gui restart and ABM scan as per post #2.

[casuk]

Enigma2-01-01-1970_01-00-27.logEnigma2-01-01-1970_01-00-19.logEnigma2-09-06-2015_17-39-38.logEnigma2-01-01-1970_01-00-20.logYes all connected and the same with only tuner b connected, if I go to sat finder tuner b is snr 98 AGC 0, tuner c, d 0% on both snr agc, and sat is the same 0% but I get a pic on sat

[abu baniaz]

As I said before, ABM uses the last tuner of type concerned. I dont know why you are mentioning tuner B only. You are confusing matters.

The frequncy used for ABM is as listed below. I hope you are checking this in sat finder.
frequency="643000" symbol_rate="6887000"system="0" fec_inner="3" inversion="2" modulation="3"

[casuk]

mine is diffrent

[abu baniaz]

You are not understanding what I am saying to you.

ABM will use the last tuner to obtain data. So you need to be checking that. If you have the sundtek setup you need to be checking Tuner E otherwise Tuner D.

Please don't believe what I say. Read the provider xml file, check what frequency ABM uses. You need to be getting a signal on the frequncy listed.

[casuk]

You are not understanding what I am saying to you.

ABM will use the last tuner to obtain data. So you need to be checking that. If you have the sundtek setup you need to be checking Tuner E otherwise Tuner D.

Please don't believe what I say. Read the provider xml file, check what frequency ABM uses. You need to be getting a signal on the frequncy listed.

mate I had to reflash it now the sundtek usb tuner wont update the driver, mate im lost on
what to do