Hm, it says: eth0: Link up, 100 Mbps Full Duplex here. But everything I have is 1000 Mbps, switch, computer etc... ;-(
sorry Double post and i could not delete the attachment
Last edited by nsw9154; 07-06-14 at 22:40. Reason: Double post
now that's strange when I transfer from my Solo2 to my windows 7 PC i regularly get 60Mbps, but I have just tried from my Miraclebox and i get 11 Mbps
2014-06-07_221130.jpg 2014-06-07_221910.jpg
And this has what to do with the GB Quad Plus ???Originally Posted by nsw9154
now that's strange when I transfer from my Solo2 to my windows 7 PC i regularly get 60Mbps, but I have just tried from my Miraclebox and i get 11 Mbps
2014-06-07_221130.jpg 2014-06-07_221910.jpg
That's very strange. Can you post a boot log? Something not right at all. The Quad Plus definitely has a 1GB ethernet adaptor.
Sorry I was not hijacking the thread I only mentioned it because my Miraclebox is supposed to have GB Lan as well but only getting 11 mbps
Maybe then start a separate thread - they are free!
It could be due to a simple patch cable. I have dozens of patch cables, allowing only 100Mbps; as soon as I change it for an other one I get 1000 Mbps.
Help asked via PM will be ignored.
The forum is there for help and all will benefit from your questions.
NO CARD SHARING TALK WILL BE TOLERATED, LAN OR WAN, IN OPEN FORUM OR PM !
English is not my native tongue.
I apologise for all my grammar, spelling and idiom errors.
No it doesn't, its 10/100.
D I S C L A I M E R
My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!
Please help keep OpenViX online, donate HERE.
Rules can be found HERE
Support our sponsor World-Of-Satellite HERE
GIGABLUE UHD QUAD 4K, VU+ DUO 4K SE, ZGEMMA H7S, VU+ UNO 4K SE
Triax 1.1m Powered by TM2600, Fixed 28.2 Zone 2 dish with GT-SAT Unicable
nsw9154 (09-06-14)
How do I save a boot log? Do you know where is it saved?
It was the cable in the house, I have now tried a new connection (that is not in a wall of the house) and it connects to 1000Mb/sek. But both cables are the same. Wierd.
Anyway, download from GBQuad Plus works with 30 MB/sec, that is ok, the cable is cat 5e, not CAT6, I usually do not get faster speeds in my house.
BUT... the upload to Quad Plus is fluctuating from 400 kb/sec to 18 Mb/sec with average then about 4 MB/sec... First I thought it is cable again, but if it goes in one way, why doesn't it go in another way with same speed? Do you get same ul and dl speeds? This fluctuation is wierd, like there were errorrs during transfer that needed to be corrected.
PS - I have now tried using FTP... WIth ftp, the transfer is 40 MB/sec upload and 50MB/sec download... Can it be the windows network neighbourhood then at fault (samba)? How can I fix that? Or is the GB Quad Plus samba at fault? I get GB speeds from my PC to my NAS so... :-( Is there any setting in GB for samba I could use?
Last edited by jerry2; 09-06-14 at 07:20.
Hi again, jerry.
I'm not sure if samba is the issue (maybe others using samba and Windows could comment). If you are now getting 40-50MB transfers using FTP, then the hardware is ok - no? All that's left is fine tuning the software environment and drivers for Quad Plus. Hopefully we will see an initial release of VIX for Quad Plus soon
Thanx, yes the HD is ok now using FTP I get the speed. I have to use Open ATV because there is no VIX and I can not get to settings on my QUad Plus for Samba so I gues something is not right there.
Posting Permissions
Reply With Quote
