Advice Needed Please

[scottmcroberts]

Hi all

Got a problem with my TM-2t that I hope someone can help me with. Lately after the box has been on about an hour or so, it slows down dramatically. EPG search is a no go area and I can have spinning vix for over half an hour before i just have to give in and hard reset it from rocker switch.

I believe I must have corrupt settings somewhere (probably due to the fact that I have been playing with it not stop since I got it about six weeks ago)

I think I need to do a full reflash which I am confident in doing but do not have a clue about how to setup my motorised dish settings. I use Disecq 1.2 at the moment and it works great but these settings were set up by someone else who has moved away. I have no idea where to start but was wondering is it possible to save these settings to my PC and then ftp them back into the box after I have done a reflash. If So that would be a plus.

If not is there a dummies guide to setting up Disecq 1.2. I was told by the installer not to use Usals as my dish cant go further than 0.8 West as it would hit my wall.

I am currently on build 678 Vix. Just need to do something to stop it from slowing down so much, got to the stage at times you can't even change a channel, sorry for longwinded post but hope the help is out there.

Thanks
Scott

[Mr. Mister]

If you go to :

Menu > Set Up > Service Searching > Tuner Configuration..

You will be able to copy down all your settings from there.. Both for tuner A and tuner B..

If you put them back in again the same way as they are now before flashing.. Then all will work again..

Make sure to double check your latitude and longitude..

[scottmcroberts]

Thanks Mr Mister, I note you mention longitude and latitude, is this not used for Usals?

[Sicilian]

Moved to the correct section.

[scottmcroberts]

apologies Sicilian

[Mr. Mister]

I have never set up a TM on usuals.. But im sure that all Vix images have the same First Install Wizard..

[scottmcroberts]

Ok, so my sat config setup at the moment is 28.2 stored in position 1 23.5 position 2 19.2 position 3 etc, usals is switched to no on all sats. Is this all I need to do? I don't need to then go into sat finder or positioner or anything like that?

[Mr. Mister]

Does it give you your latitude and longitude.. ??

I have never set up a box storing every position.. like you have..

I always us usals ..

[scottmcroberts]

Think I am gonna go for Usals and give it a go is there a tutorial on setting this up, I have my latitude and longitude from dishpointer, longitude is a minus which I presume means west. WHat would you do if doing a complete flash and starting from scratch. sorry to be pain but I am clueless when it comes to this side of it

[Mr. Mister]

What would i do with what buddy.. ??

Im not sure what your asking..

[scottmcroberts]

Sorry my good man, I was very unclear there, if you were reflashing your stb completely and not restoring settings, when the the tuner configuration option comes up.

I presume Tuner A should be Simple, Positioner, My Longitude and. Latitude. is that all i need to to enter for usals?

WHich position should my dish be on to start with?
What should I select for tuner B?

God I feel a dumba*s tonight, again apologies for all the questions

[rossi2000]

if you want to setup usuals.

reflash your box and then setup tuner A as usals and enter your lat/long details, setup tuner b as second input from a motor lnb i think it is.

the latitude with the minus if for eg its -2.43 just enter 2.43.
thats it.

[rossi2000]

0.8w is usually the one to test with. once youve entered your lat/long go to 0.8w on your channellist and check snr's and tweak from there.

[scottmcroberts]

ok here we go then just about to reflash, will let you know how I get on...would be so much easier if If I could just ftp current satellite settings back in after reflash

[scottmcroberts]

OK reflashing at moment, moved dish to 0.8 before i begun..........