D I S C L A I M E R
My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!
Please help keep OpenViX online, donate HERE.
Rules can be found HERE
Support our sponsor World-Of-Satellite HERE
GIGABLUE UHD QUAD 4K, VU+ DUO 4K SE, ZGEMMA H7S, VU+ UNO 4K SE
Triax 1.1m Powered by TM2600, Fixed 28.2 Zone 2 dish with GT-SAT Unicable
D I S C L A I M E R
My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!
Please help keep OpenViX online, donate HERE.
Rules can be found HERE
Support our sponsor World-Of-Satellite HERE
GIGABLUE UHD QUAD 4K, VU+ DUO 4K SE, ZGEMMA H7S, VU+ UNO 4K SE
Triax 1.1m Powered by TM2600, Fixed 28.2 Zone 2 dish with GT-SAT Unicable
I had the same problem and this worked for me on my tv remote I pressed the energy saving button and put it to maximum it makes ur tv dim and that's it my remote was responding fine
putting a fresh set of Duracell batteries in the remote instead of the shitty chineese ones that came with it and changing the remote code to 1 and doing the same on the receiver seemed to have fixed it.
you were right. when I put my tv into standby and use the lcd screen on the solo2 as a guide. its perfect. and I do have energy saving mode. but it is not enabled atm. any ideas how to fix as changing tvs is not an option
Cover the IR sensor on the box COMPLETELY with masking tape.( The Sensor is between the power button and the display. ) This will filter out plasma interference and only leave through valid signals. If it's still not working 100%, stick on another layer of tape. Get the black marker out, blend it in a bit!
In fairness, if u paint it black and cut it to the right size, it's barely noticeable. Infinitely better than button bashing the remote. 300 quid pays for a powerful twin tuner satellite box, if you want good looks, stick on a Mila Kunis film!
I setup my new solo2 today and lo and behold had the unresponsive remote problem. I had already enabled power save mode on my plasma in anticipation. Moved the solo2 to the bedroom with a led TV and the problem vanished. Reinstalled the faithful duo in the lounge.
What gets me is the remotes for my Duo and Solos are fine, just the solo2 that plays up.....
No issues here with my Panny Plasma.
D I S C L A I M E R
My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!
Please help keep OpenViX online, donate HERE.
Rules can be found HERE
Support our sponsor World-Of-Satellite HERE
GIGABLUE UHD QUAD 4K, VU+ DUO 4K SE, ZGEMMA H7S, VU+ UNO 4K SE
Triax 1.1m Powered by TM2600, Fixed 28.2 Zone 2 dish with GT-SAT Unicable
Help asked via PM will be ignored.
The forum is there for help and all will benefit from your questions.
NO CARD SHARING TALK WILL BE TOLERATED, LAN OR WAN, IN OPEN FORUM OR PM !
English is not my native tongue.
I apologise for all my grammar, spelling and idiom errors.
This is a known problem with plasmas and applies to Dreamboxes and many other STB-s! What you can do is put masking tape on the INSIDE of the Solo2 before IR sensor. Take the front of, put masking tape....Void warranty if you break something of course...
Google: "IR PLASMA INTERFERENCE" and you will find TONS of info on that topic. This is in no way Solo2 problem it a general problem with plasmas and IR receivers....
Hespy (18-01-13)