just setup my new solo2 and fully updated it. and I find that my remote is not responding when it should. like I will press down and it wont shift down until after a few presses. when I press exit it doesent exit unless I press it a few times and so on.
Last edited by warajoker; 15-01-13 at 22:58.
What make & model of TV are you using?
its a Samsung ps43d450a2wxxu but im not using the remote to control the tv. only the solo2Originally Posted by judge
Test by moving the box to an other location or shut down the TV. Some TV's are known to cause IR-interference.
Help asked via PM will be ignored.
The forum is there for help and all will benefit from your questions.
NO CARD SHARING TALK WILL BE TOLERATED, LAN OR WAN, IN OPEN FORUM OR PM !
English is not my native tongue.
I apologise for all my grammar, spelling and idiom errors.
And so do some types of energy saving bulb !
Have you tried new batteries ?
Have you removed the protective film from the front of the display ?
D I S C L A I M E R
My right to post information is protected under the rights for freedom act. In all instances, information here on my posts are hypothetical in nature, out of curiosity, common knowledge, public knowledge, or role-play. Use of the collective descriptions and knowledge from any of my posts are at YOUR discretion
I am not responsible for what you do with it
Want to know about cardsharing see Here
Want clone support see Here
PM HELP WILL BE IGNORED PLEASE POST IN FORUM AS IT BENEFITS EVERYONE
If you have had a problem that you started a thread about and found your own solution please post back to let everyone know how you solved it
I don't think its the tv as I used to have a vu+uno and never had this problem.
I have removed all the plastic filming but I will test it with new batteries
Have you installed a HDD in the unit? Did you initialise it in the unit? do you have picons on the HDD?
D I S C L A I M E R
My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!
Please help keep OpenViX online, donate HERE.
Rules can be found HERE
Support our sponsor World-Of-Satellite HERE
GIGABLUE UHD QUAD 4K, VU+ DUO 4K SE, ZGEMMA H7S, VU+ UNO 4K SE
Triax 1.1m Powered by TM2600, Fixed 28.2 Zone 2 dish with GT-SAT Unicable
yes I have installed a hardrive and I have installized it but yesterday when I setup timers to record something I got write error and no I have no picons. but I did have the plugin flash expander which I have now deleted
ive changed the remote control code to number 1 and it seems to working better
But this is not about the UNO; this is about the Solo2 you're having a problem with.
And 'thinking' is of no use: 'knowing' is what you will do once you turned off the TV and any energy saving bulbs.
What's the point in asking advise and not following it
Help asked via PM will be ignored.
The forum is there for help and all will benefit from your questions.
NO CARD SHARING TALK WILL BE TOLERATED, LAN OR WAN, IN OPEN FORUM OR PM !
English is not my native tongue.
I apologise for all my grammar, spelling and idiom errors.
i switched the tv of and i have no enegery saving bulbs
Last edited by warajoker; 16-01-13 at 10:30.
And the result is......?
Help asked via PM will be ignored.
The forum is there for help and all will benefit from your questions.
NO CARD SHARING TALK WILL BE TOLERATED, LAN OR WAN, IN OPEN FORUM OR PM !
English is not my native tongue.
I apologise for all my grammar, spelling and idiom errors.
warajoker (16-01-13)
nothing changed mate. i found that switch the remote to mode 1 worked the best
It CAN happen, that IR receiver led in the Solo2 could not be aligned properly, so you can check that too. I already saw such problem in some other receivers (it can happen in production, slightly bend down for example). Same could apply to remote control LED. So check that too.
If you have Plasma TV that could be culprit, but you said you tested it with TV switched off (TOTALY OFF, not just standby!).
Posting Permissions
Reply With Quote
