The box hasnt been on for a couple of days,turned on tonight its gets to the screen with with the girl with bloodshot eye (loading defaults) then flicks to green screen than gets in a re boot loop...cant connect with browser or ftp program.......any ideas? cheers
if the unit keeps going green, it sounds like it need a reflash, I do not own the solo, so cant offer any other remidy
baz
Units; VU+Ultimo/duo/DM800/7020HD/tm9100
1.2 channel master/quad feedhorn/36volt /vbox
1 fixed dish, and 1 motorized 1mtr dish
and a pile of redundant cards/cams
wasn't sure if there was a way to get to a boot menu,on the itgate you can get into boot menu holding VOL + when switching on
well unless its urgent, i would wait 24 hours, to see if there are any alternitives
baz
Units; VU+Ultimo/duo/DM800/7020HD/tm9100
1.2 channel master/quad feedhorn/36volt /vbox
1 fixed dish, and 1 motorized 1mtr dish
and a pile of redundant cards/cams
By what you've described I would re-flash using USB method. Use VTI image and replace the drivers here http://www.vuplus-support.co.uk/show...10-USB-Drivers
Where you doing anything that might have caused a green screen? What was the last thing you changed/installed?
D I S C L A I M E R
My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!
Please help keep OpenViX online, donate HERE.
Rules can be found HERE
Support our sponsor World-Of-Satellite HERE
GIGABLUE UHD QUAD 4K, VU+ DUO 4K SE, ZGEMMA H7S, VU+ UNO 4K SE
Triax 1.1m Powered by TM2600, Fixed 28.2 Zone 2 dish with GT-SAT Unicable
last time it was on,was put into deep standby....not used for a couple of days,powered up tonight and the green screen loop........will try & get into it tomorrow,,,,pain in the a**e having to start from scratch.....motorised dish,cccam,plugins,replacing drivers.....OMG.....suppose that'll keep me busy for a while.......never flashed one of these only the dreambox,itgate & the old cable boxes....so i may be asking some questions..
Dont worry, very easy to flash. Guide here http://www.vuplus-support.co.uk/show...with-USB-stick
Have you never flashed it since you bought it? Surprised you even managed to get you motor to work with the stock release image. What image was on it out of interest?
D I S C L A I M E R
My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!
Please help keep OpenViX online, donate HERE.
Rules can be found HERE
Support our sponsor World-Of-Satellite HERE
GIGABLUE UHD QUAD 4K, VU+ DUO 4K SE, ZGEMMA H7S, VU+ UNO 4K SE
Triax 1.1m Powered by TM2600, Fixed 28.2 Zone 2 dish with GT-SAT Unicable
Originally i had a bit of trouble getting it set up due to the drivers missing,so once i got the drivers installed it's been ok till the wife & kid get there hands on it,wouldn't care 95% of the channels they watch are on freesat...
will have a go at flashing later today (hopefully) weren't the days of cable boxes so easy .....click on restore on my pc to ip address and away it went back to its original state (itgates by the way) all channels where i put them....Ahhh......
Posting Permissions
Reply With Quote
