Disec set up on BH Image HELP

[satplustv]

Hello

I have just flashed the "BH.1.7.2.USB.FULL.BACKUP.OSCAM6346/CCcam2.1.3.$LYUK-READY FOR UNO BY CAZUELA" image and its defaults to a motor set up and i need to configure it to Disec and i seem to be getting no where fast...

The set up i want is:

DISEC:

Port a Astra 28.2
Port b Eutelsat W1
Port c Nothing
Port d badr sat

Can anyone help please

[Sandman]

Hello

I have just flashed the "BH.1.7.2.USB.FULL.BACKUP.OSCAM6346/CCcam2.1.3.$LYUK-READY FOR UNO BY CAZUELA" image and its defaults to a motor set up and i need to configure it to Disec and i seem to be getting no where fast...

The set up i want is:

DISEC:

Port a Astra 28.2
Port b Eutelsat W1
Port c Nothing
Port d badr sat

Can anyone help please

Heres a quick guide -

How to setup Vu+ with VBox II DiSEqC 1.2 Positioner.

If your VBox II already has the satellite positions stored and your changing from an old receiver to Vu+ then follow this procedure.

Write down your VBox II satellite position numbers. These are the numbers displayed on the front of the VBox II when moving to a
specific satellite position. These position numbers can also be found in your old receivers motor setup menu.

Example lets say...
Position 1 on VBox II = Astra 19e
Position 2 on VBox II = Eutelsat W2 16e
Position 3 on VBox II = Hotbird 13e

You get the idea...

First send the dish to Astra 19e using Vbox II.

On Vu+ Remote Press Menu
Select Setup Press OK
Select Service Searching Press OK
Select Tuner configuration Press OK
Select Tuner A Press OK

Now set Configuration Mode to Advanced. Use Left or Right keys on remote to select.

Configuration Mode: Advanced
Satellite: Astra 19e
LNB: 1
DiSEqC mode: 1.2

Scroll down to botton of the page with the down arrow on remote.

Stored position: 001

Press OK to store.

OK that's Astra 19e setup now to setup Eutelsat W2 16e

Now send the dish to Eutelsat 16E using Vbox II.

Select Setup Press OK
Select Service Searching Press OK
Select Tuner configuration Press OK
Select Tuner A Press OK

Configuration Mode: Advanced
Satellite: Eutelsat W2 16e
LNB: 2
DiSEqC mode: 1.2

Scroll down to botton of the page with the down arrow on remote.

Stored position: 002

Press OK to store.

OK that's Eutelsat W2 16e setup now to setup Hotbird 13e

Now send dish to Hotbird using Vbox II

Select Setup Press OK
Select Service Searching Press OK
Select Tuner configuration Press OK
Select Tuner A Press OK

Configuration Mode: Advanced
Satellite: Hotbird 13e
LNB: 3
DiSEqC mode: 1.2

Scroll down to botton of the page with the down arrow on remote.

Stored position: 003

Press OK to store.

You get the idea, now repeat for the rest of the satellites and your done.

This is enough to get you started, the fun starts learning the rest.

----
Courtesy of **********

[satplustv]

It does not seem to be storing the positions ?

[Sicilian]

Are you using a Diseqc 4 way switch?

If so: -

Menu > Setup > Service Searching > Tuner configuration.

Config mode = simple
Mode = Diseqc A/B/C/D

Then set your ports/satellite.

Dig out your Uno manual page 22

[satplustv]

How silly am i ?

I knew i was missing something simple !

Now i have done that and still have a problem it says no data transponder when i select a channel ?

[Sicilian]

Have you upload your own settings & bouquets? Have run a re-scan? Are you using latest FPGA?

[satplustv]

Have you upload your own settings & bouquets? Have run a re-scan? Are you using latest FPGA?

I have uploaded my own channel list as normal !

I do not know what you mean by FPGA ?

[satplustv]

Got it working by doing a FPGA Update via the plug ins menu, thanks :-(

I would still like to know what the hell a FPGA update is as its the 1st time i have ever had to do it ?

[Sicilian]

Its firmware for the tuner.

[Larry-G]

Got it working by doing a FPGA Update via the plug ins menu, thanks :-(

I would still like to know what the hell a FPGA update is as its the 1st time i have ever had to do it ?

as said its basically a firmware update and reprograms the chip that controls the tuner card.

[satplustv]

as said its basically a firmware update and reprograms the chip that controls the tuner card.

Thanks, how come i have only had this problem now and not on previous image changes ?