Hello Guest, if you are reading this it means you have not registered yet. Please take a second, Click here to register, and in a few simple steps you will be able to enjoy our community and use our OpenViX support section.
Results 1 to 7 of 7

Thread: A little help please!

  1. 23-01-12, 20:11 #1
    v_j_r

    A little help please!

    I need some help as new owner of VU+ Ultimo, i originally have a DM8000 (which i still have) in which i was using Cccam the CFG file i was using was one created that included a boxkey for my N** card UK.

    I have FTP'ed this CFG file to my ultimo but CAM info shows that it is not seeing the cardreaders? is the format different in the VU+ is there a CFG creator availible for use with the ultimo please any help would be gratefully recieved.


    Regards.
    Reply With Quote Reply With Quote
  2. Sponsored by World-of-Satellite.co.uk
  3. 23-01-12, 20:21 #2
    fintannl
    fintannl is offline
    Title
    Forum Supporter
    Donated Member
    Join Date
    Aug 2010
    Posts
    723
    Thanks
    104
    Thanked 80 Times in 56 Posts
    check the sci value in the config and make sure you put the card in the correct sci slot be it sci0. sci1 or whatever
    Reply With Quote Reply With Quote

  4. The Following User Says Thank You to fintannl For This Useful Post:

  5. 23-01-12, 20:31 #3
    Trial
    Trial is offline
    Title
    Moderator
    Join Date
    Jul 2011
    Location
    germania
    Posts
    5,126
    Thanks
    106
    Thanked 1,434 Times in 1,137 Posts
    Hi,
    which image do you use? In an original image vucamd already uses the reader. If you are on OI edit bootup file and remove vucamd or rename CCcam to vucamd or use ViX.

    ciao
    ---
    Sat:VU+ Ultimo4K/Solo4K/Duo2/2*Solo2/Ultimo
    Remote: Harmony 200, 700, Link, Smart Control, Smart Companion, Elite, 2*Ultimate, Keyboard
    Reply With Quote Reply With Quote

  6. The Following User Says Thank You to Trial For This Useful Post:

  7. 23-01-12, 20:45 #4
    bassethound's Avatar
    bassethound
    bassethound is offline
    Title
    Forum Supporter
    Donated Member
    Join Date
    May 2010
    Location
    North West
    Posts
    5,719
    Thanks
    6,871
    Thanked 6,130 Times in 2,737 Posts
    Move to the correct section!

    Dont post questions in the downland section!
    All PM,s asking about c/s on cable will be ignored and reported to forum staff!
    Reply With Quote Reply With Quote
  8. 23-01-12, 21:40 #5
    v_j_r
    Where are the softcams etc in Vix image many thanks.


    Regards.
    Reply With Quote Reply With Quote
  9. 23-01-12, 21:47 #6
    fintannl
    fintannl is offline
    Title
    Forum Supporter
    Donated Member
    Join Date
    Aug 2010
    Posts
    723
    Thanks
    104
    Thanked 80 Times in 56 Posts
    not available on vix. found at
    HTML Code:
    http://www.4shared.com/dir/wnyHV50A/VIX_CAMS.html
    just load into /tmp folder and use the ipk installer to load
    Last edited by Stanman; 23-01-12 at 23:04. Reason: edited live link
    Reply With Quote Reply With Quote

  10. The Following User Says Thank You to fintannl For This Useful Post:

  11. 23-01-12, 23:04 #7
    Stanman's Avatar
    Stanman
    Stanman is offline
    Title
    Junior Admin
    Donated Member
    Join Date
    May 2010
    Posts
    11,284
    Thanks
    1,035
    Thanked 3,599 Times in 2,632 Posts
    No live links please.

    Support The Sponsor - Buy from the best HERE
    Please abide by the rules - have a read HERE
     VIX manual & guides >>HERE
     Download images from >> HERE
     New Box Setup Guide >>HERE

    D I S C L A I M E R
    My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!

    PM HELP WILL BE IGNORED PLEASE POST HERE IN FORUM AS IT BENEFITS EVERYONE

    Follow us on Twitter

    NO CARD SHARING TALK WILL BE TOLERATED, LAN OR WAN! IN OPEN FORUM OR PM

    IF THE POSTS HELP PLEASE CLICK THANKS OR ADD TO REP ?

    Reply With Quote Reply With Quote
« Wlan on ultimo anyone using | Smargo on Ultimo »

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

This website uses cookies
We use cookies to store session information to facilitate remembering your login information, to allow you to save website preferences, to personalise content and ads, to provide social media features and to analyse our traffic. We also share information about your use of our site with our social media, advertising and analytics partners.
     

Options

About

Welcome to Satellite Support Forum .: Home of OpenViX Team:.!

World-of-Satellite enthusiasts Satellite, IPTV, Technology, Audio visual Forum.

Any information provided on this site is not guaranteed in any way. Some articles may discuss topics that are illegal, so this information is provided for educational purposes only, your use of the content, downloads and files, or any part thereof, is made solely at your own risk and responsibility. Viewing Pay TV without a valid subscription is illegal. !! World-of-Satellite.com cannot be held responsible for the content of any information stored or posted on this forum.

Site Links

Social Media