CIFS mount impossible on VIX 2.3

[ablyes]

On VIX 2.1 :
i can mount the hard disk of my box as guest user (freebox, french box with NAS of 250 GB).

On VIX 2.2.1 OR 2.3 :
i can't mount the same disk with same parameters ! it says that the mount is done, but the disk is not mounted on the interface.
Also not detectec when i go to see all my hard disks.

What can i do ? Is it a known bug ?

Thank you

[martinakis]

I have same problem,can not choice shared derictory in recording settings.

[Sicilian]

See screenshot for settings.

[ablyes]

Yes, i complted like this. I first run a network discovery, then i saw what you is on the image you've posted.
It also asked me to enter login/password parameters, what i did.

I say you, it works on 2.1 and not on 2.3 !
Can you try with guest user ? with password guest, or empty password, ... (i tried).

[Larry-G]

Yes, i complted like this. I first run a network discovery, then i saw what you is on the image you've posted.
It also asked me to enter login/password parameters, what i did.

I say you, it works on 2.1 and not on 2.3 !
Can you try with guest user ? with password guest, or empty password, ... (i tried).

when asked to enter a password simply select no, this is how i mount my NAS between my Duo and Uno using ViX 2.3.

[martinakis]

See screenshot for settings.

Thenks,
I show my mistake,local share name and server share name are another.
Now I can record tv on my pc hard drive.

[ablyes]

when asked to enter a password simply select no, this is how i mount my NAS between my Duo and Uno using ViX 2.3.

I tried with non when the clarke asked me to enter a couple login/password.
I can't still mount my NAS :-(

[ablyes]

Nobody can help me please ? Even with root/password access, it doesn't work

[silverfox0786]

when you mount a CIFS

do not add a username or password in the passwords section as bellow

screenshot.jpg

you will be asked the moment you press ok on a CIF location to add username/password say NO

then from there you will see this screen

screenshot.jpg

then add yr username and password as per this screen above including all ip and folder names

once done it will say mount point created

as a double measure click mount again and restart the box

your mount will be seen

sometimes if its not see then you will need to create a folder on box

accourding to my screenshot above the folder i am using is Recordings

so i will FTP to receiver and navigate to media/net

and create folder Recordings

again restart box

and all should be seen

[BadBoy]

I have done the above but my box is still not showing my mounted drive?

[silverfox0786]

have you tried NFS

since upgrading my QNAP to Synology

i have noticed CIFS is not supported and can only mount via NFS

make sure NFS privalages is

192.168.0.0/255.255.255.0

[BadBoy]

I will give that a try

Sent from my Galaxy Nexus using Tapatalk

[ablyes]

My NAS does't offer NFS service Juste cifs

[supra59uk]

I had the same problems when setting my nas drive up, i could see it but i couldnt use it the problem was the actual settings in my nas box not set the right sharing privilages once i did that the little x disappered off the mount in mount manager and then i could change the settings to use the nas drive as the hard drive, so dbl check the settings in your nas box and make sure you have sett all the rights so the xtrend can access it.

[BadBoy]

Nfs does not work for me either, I do have the red cross on the drive but can access it via windows

Sent from my Galaxy Nexus using Tapatalk