New VTi "Vu+ Solo Team Image" - V0.1-1.07.2010 or official 4.6 - Post feedback here!

[hansham]

encryption? no idea, it is an official Canaldigitaal card.

[Sicilian]

encryption? no idea, it is an official Canaldigitaal card.

You are not doing yourself posting all over the forums the same questions.

Keep this topic in the thread here http://www.vuplus-support.co.uk/show...stalling-CCcam If you post in anymore sections the same question I will delete them. Now please just keep your question in one thread so that we can keep track of what your are doing/trying.

[hansham]

So far it is an improvement, but when it starts I get this staring woman and in the upper left corner it says:
"loading defaults...."

and the text "loading defaults...." never goes away. I think that is not good.
By the way, nowhere is explained what defaults are. What are defaults?? What is the purpose of this message?

[paul362]

if its stuck on loading Defaults then press the ok button and check your AGC and SNR rates (presuming you have channels loaded already) if you have not loaded the files mentioned earlier by Sic you will have 0 and 99% in the signal because you need the new drivers for the tuner to work properly.

If on the other-hand you have not loaded the Default channels and have loaded the new drivers (as instructed by Sic) then just go ahead and download your chosen channel package either from the vti panel or use dream-set or your favorite programmer to send them over after this reboot and you should be up and running fine.

PS: loading Defaults just means the box is booting up as normal.

[appc777]

I have just flashed the solo with the latest vti image.

my sys config as follows
3 fixed sat connected to diseqc 4x1
sat1@diseqc 1 >>port A
sat2@diseqc 2 >>port B
sat3@diseqc 3 >>port C

solo config as follows
config mode=simple
mode=diseqc A/B/C/D
port A sat1
port B sat2
port C sat3
set voltg=yes
send diseqc =no

first time before drivers updated all 3 sats get no signal / always on 99%
but when i installed the drivers attached to the post (mbox-dvb-modules_2.6.18-7.3-r20-20100611_vusolo.zip). sat1@diseqc 1 >>port A + sat2@diseqc 2 >>port B work 100%.
but sat3@diseqc 3 >>port C get no signal / always on 99%
please need your help

BTW:
1- tested same sys config with others receivers (humax5400)and all 3 sats work 100%.
2- changed 4x1 switch still same .

[Sicilian]

I have just flashed the solo with the latest vti image.
my sys config as follows
3 fixed sat connected to diseqc 4x1
sat1@diseqc 1 >>port A
sat2@diseqc 2 >>port B
sat3@diseqc 3 >>port C
first time before drivers updated all 3 sats get no signal / always on 99%
but when i installed the drivers attached to the post (mbox-dvb-modules_2.6.18-7.3-r20-20100611_vusolo.zip). sat1@diseqc 1 >>port A + sat2@diseqc 2 >>port B work 100%.
but sat3@diseqc 3 >>port C get no signal / always on 99%
please need your help

BTW: I tested same sys config with others receivers (humax5400)and all 3 sats work 100%.

Can you test with the latest official image and report back please? http://www.vuplus-support.co.uk/show...mage-Ver.-5.1a

[appc777]

Can you test with the latest official image and report back please? http://www.vuplus-support.co.uk/show...mage-Ver.-5.1a

thanks for reply
do i have to update drivers or just install latest official image

[appc777]

Can you test with the latest official image and report back please? http://www.vuplus-support.co.uk/show...mage-Ver.-5.1a

I did a test with latest official image no help problem still exists

[grtmoby]

- what if u put third cable on port D.
- exchange A & C

see and write down what u get at each case

[appc777]

- what if u put third cable on port D.
- exchange A & C

see and write down what u get at each case

I did all kind of swapping between cables on different ports after all theses tests I found out I can not connect more than 2 fixed satellites in different diseqc. Only 2 fixed satellites and the others no signal / always on 99%

BTW:1- tested same sys config with others receivers (humax5400)and all 3 sats work 100%.

[grtmoby]

ok it is working on the humax,

can u try with another diseqc switch. will u post a screen shot of ur confg

[appc777]

ok it is working on the humax,

can u try with another diseqc switch. will u post a screen shot of ur confg

yes i did try with another 2 diseqc switch. but no help

[grtmoby]

try to change send diseqc command to "yes"

[appc777]

try to change send diseqc command to "yes"

still no help

[world-of-satellite.co.uk]

I would email vuplus. Looks like you exhausted the possibilities and it could be a bug in the software. Send an email to: -

alex@vuplus.com