I am having trouble with this Vu+util. Does anyone know how to put in the image?
I am trying com1. I have entered the Ip's
But I cannot fathom how to enter the image.
Can anybody help please,
Regards,
colin
Why do you want to use VU Utility? Why dont you just flash using the USB method?Originally Posted by colinbrown5013
D I S C L A I M E R
My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!
Please help keep OpenViX online, donate HERE.
Rules can be found HERE
Support our sponsor World-Of-Satellite HERE
GIGABLUE UHD QUAD 4K, VU+ DUO 4K SE, ZGEMMA H7S, VU+ UNO 4K SE
Triax 1.1m Powered by TM2600, Fixed 28.2 Zone 2 dish with GT-SAT Unicable
Because I cannot, it will not flash. i am at my wits end trying to get this image into my Vu+uno.
I am ready to abandon, I have never had so many problems.
Its the blackhole image, I have tried to flash it at least 100 times.
Colin
Last edited by colinbrown5013; 17-08-11 at 16:34. Reason: Missed something out
We for starters you could try posting in the correct section. Start a topic in the VU+ Uno section please with the issues you are having.
D I S C L A I M E R
My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!
Please help keep OpenViX online, donate HERE.
Rules can be found HERE
Support our sponsor World-Of-Satellite HERE
GIGABLUE UHD QUAD 4K, VU+ DUO 4K SE, ZGEMMA H7S, VU+ UNO 4K SE
Triax 1.1m Powered by TM2600, Fixed 28.2 Zone 2 dish with GT-SAT Unicable
make sure you have first formatted the usb stick to fat32 then place the folder vuplus onto your stick. make sure it looks like this
usb stick > vuplus ( folder ) > uno (folder) > the four flash files.
also try the rear usb ports as i find my receiver tends not to like being flashed from the front port. insert the stick and switch the receiver off from the power button on the rear, wait approx 30 seconds then power back on, you should see a prompt to press channel - button on the receiver ( not remote ) make sure you do this within 10 seconds otherwise it will bypass the stick and boot as normal.
My posts contain my own personal thoughts and opinions, they do not represent those of any organisation or group but my own.
If you don't like what I post, Don't read it.
SIMPLES.
moved posts to appropriate section.
My posts contain my own personal thoughts and opinions, they do not represent those of any organisation or group but my own.
If you don't like what I post, Don't read it.
SIMPLES.
I have posted How does a dummy start over.
I was advised Vu+util But I cannot get the image in. So I looked around and found a post on the subject.
The way my luck is going Leicester will probably lose again.
Regards,
Coliun
try as suggested in my above post. see if it will flash by using a rear usb port.
My posts contain my own personal thoughts and opinions, they do not represent those of any organisation or group but my own.
If you don't like what I post, Don't read it.
SIMPLES.
Posting Permissions
Reply With Quote
