Service ID problem when changing channel while recording.

[twol]

What are the dates for .20 and ,21 from the Menu/information/about screen???

[heebo1974]

What are the dates for .20 and ,21 from the Menu/information/about screen???

I don't have .21 anymore installed.
.20 info:
5.0.020
Drivers 2017-05-22
Kernel 3.13.5
GStreamer 1.11.2 (git)
Python 2.7.12
Installed: 2017-09-16
Updated 2017-06-23

[twol]

Dear heebo 1974
I have a similar problem with reading the PAT. With all versions >020. After installing only VIX and reloading the channels through dreamboxedit. I only could the the startup channel. When zapping I got everywhere timout reading PAT. I reported this with version 5.0.021 and updated my thread. Sofar nobody found a solution.

Let's cross the fingers that somebody finds the bug.
nekrub2

Are you using a CI card?

[heebo1974]

Are you using a CI card?

Yes, but problem exists with or without CI card. I have tested both.

[twol]

OK, thanks.
With OpenATV which version(s) work (6.0, 6.1?) and when did you try them? Epecially, when have you tried recently?
Just trying to identify when it has worked with OpenATV

[nekrub2]

Dear all
I just installed 5.1.002 with USB flash and restored the 5.0.020 settings. Same PAT-time-out behaviour.

[jukkal2]

Hello again again...
Today I installed fresh OpenVix 5.1 and test same thing again. And the result was again the same.
Here is the new debug log.
I think that developer team does not even bother to take this thing seriously.

Oh shit, I also flashed 5.1.002 yesterday.
So it will probably eventually back to 5.0.020 again. But I'll wait until I see the problem appear in my own box.

[heebo1974]

OK, thanks.
With OpenATV which version(s) work (6.0, 6.1?) and when did you try them? Epecially, when have you tried recently?
Just trying to identify when it has worked with OpenATV

Working fine with 6.1
Kernel 3.13.5
Drivers 2017-05-22
Gstreamer 1.13.0 (GIT)
Python 2.7.13
Installed 2017-09-03
Updated 2017-08-18

BUT I today tested with latest Open ATV 6.1 (2017-11-21) and it does not work. It is even worse than OpenVix above .020 versions.
If I make same procedure I cant anymore get lock to channnel without starting enigma2 again !

[twol]

Working fine with 6.1
Kernel 3.13.5
Drivers 2017-05-22
Gstreamer 1.13.0 (GIT)
Python 2.7.13
Installed 2017-09-03
Updated 2017-08-18

BUT I today tested with latest Open ATV 6.1 (2017-11-21) and it does not work. It is even worse than OpenVix above .020 versions.
If I make same procedure I cant anymore get lock to channnel without starting enigma2 again !

Thanks, very interesting - thats a big help and points to one update in both ViX (in 021) and then included later in a big update to OpenATV at the end of September.

[Huevos]

020: 27 June
021: 05 July

[Huevos]

Thanks, very interesting - thats a big help and points to one update in both ViX (in 021) and then included later in a big update to OpenATV at the end of September.

Which update?

[twol]

Which update?

read this http://www.world-of-satellite.com/sh...465#post461465
Vu drivers didn't change between 020 and the ATV image posted in #23

[Huevos]

Guys can you please try this developer image so we can narrow down a bit further.

Link removed. Issue confirmed in 5.0.021.001.developer

[cactikid]

would you advise a fresh install and no settings restore for his problem?

[abu baniaz]

If you are fault finding, you normally try to keep things as "clean" as possible. So no restores, bare minimum install.