chip face down in the card readers in the smargo chip up.
chip face down in the card readers in the smargo chip up.
D I S C L A I M E R
My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!
Please help keep OpenViX online, donate HERE.
Rules can be found HERE
Support our sponsor World-Of-Satellite HERE
GIGABLUE UHD QUAD 4K, VU+ DUO 4K SE, ZGEMMA H7S, VU+ UNO 4K SE
Triax 1.1m Powered by TM2600, Fixed 28.2 Zone 2 dish with GT-SAT Unicable
Ok, tested. Imo the ecm times reported by the ET9000 are wrong. Picture is spot on, no glitching/freezing whatsoever.
Top slot: -
BOXKEY: /dev/sci1 XX XX XX XX
SMARTCARD CLOCK FREQUENCY: /dev/sci1 3580000
Bottom slot: -
BOXKEY: /dev/sci1 XX XX XX XX
SMARTCARD CLOCK FREQUENCY: /dev/sci1 3580000
Smago: -
BOXKEY: /dev/ttyUSB0 XX XX XX XX
SERIAL READER : /dev/ttyUSB0
SMARTCARD CLOCK FREQENCY : /dev/ttyUSB0 6000000
Tested as a client too (we wont talk any further about that).
Tested with CCcam 2.1.3 & 2.2.1.
D I S C L A I M E R
My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!
Please help keep OpenViX online, donate HERE.
Rules can be found HERE
Support our sponsor World-Of-Satellite HERE
GIGABLUE UHD QUAD 4K, VU+ DUO 4K SE, ZGEMMA H7S, VU+ UNO 4K SE
Triax 1.1m Powered by TM2600, Fixed 28.2 Zone 2 dish with GT-SAT Unicable
canthackit (04-06-11)
nightmare.
i've now put the BH image on (bit ancient still refers to the DVI connection)
now running cccam 2.2.0
disabled everything (you know what i mean)
card in lower slot, chip down
it's on /sci1
and nothing blank screen.
i've tried putting the cccam 2.2.1 i have still nothing got a feeling my version won't work
but anyway still on 2.2.0 and nothing
so come on guy's what am i doing wrong
your obidient servent
canthackit....................it's never been truer
cant believe it
4 pages and i still aint sussed it
Check your pm.
D I S C L A I M E R
My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!
Please help keep OpenViX online, donate HERE.
Rules can be found HERE
Support our sponsor World-Of-Satellite HERE
GIGABLUE UHD QUAD 4K, VU+ DUO 4K SE, ZGEMMA H7S, VU+ UNO 4K SE
Triax 1.1m Powered by TM2600, Fixed 28.2 Zone 2 dish with GT-SAT Unicable
this is getting crazy i'm in the process of going back to the vix image.
now i cant get the bloody thing to install, it just sits there saying flashing and nothing is happening, i've tried both versions posted here the one with the updated drivers and the one without, and neither will install.
Black Hole went on ok...so what am i doing wrong with VIX?
i don't believe that this image takes 5 minutes to install let alone the 10 mins i've left it for now, this just gets sillier and sillier
i need to get this sorted now before i can even go back to the card problem
regards: canthackit
Last edited by canthackit; 04-06-11 at 08:10.
Can't help with the flashing but you need to use the VIX image as the BH one is old and it was known that the drivers were no good for the internal card readers at the time of release.
Vu Duo 4K - Vu + Solo4K - Vu + Uno4K - Vu+Uno - Vu+Ultimo4K - Vu+ Zero - Vu+Solo-SE (In Black Evo ) - PrismCube
ok thanks mate but as the post above say's.
i cant get the bloody thing on there.
i'm in the process of downloading and trying to install yet again and the bleedin' is just sitting there saying "flashing"
Have u tried formatting the usb stick, and then copy the files over again?
Sent from my MB511 using Tapatalk
about 15 times now mate over the course of a couple of hours.
i've tried the front usb port the rear usb ports, i've formatted the pen everytime i'm on a mac so it was ms-dos fat copied over the et9000 folder with the 4 files, power off, put the usb in the front port, power on, it recognises the VIX image then when it says ready press ok button on the front panel......................
then wait 30 mins while it says "flashing"..................................i' m still waiting it's never going to install.
the only other thing i've just found another usb pen i'm going to try that.
regards: canthackit
Last edited by canthackit; 04-06-11 at 09:08.
Try loading the factory image on it
Have you tried flashing with everything else disconected such as sat cable, HDMI, HDD, smagro and anything that can be removed remove.
Vu Duo 4K - Vu + Solo4K - Vu + Uno4K - Vu+Uno - Vu+Ultimo4K - Vu+ Zero - Vu+Solo-SE (In Black Evo ) - PrismCube
ok going to try disconnecting everything to install the vix image if that dont work, i'll try with everything disconnected to install the factory image.
i'm on the point of thinking about asking steffan if there's any possibiltiy of exchanging this box for another Duo, he can only say "No"...............or sod off
thanks & regards: canthackit
everything disconnected the VIX image wont install
Does this box offer another way to flash such as via a serial port ?
Vu Duo 4K - Vu + Solo4K - Vu + Uno4K - Vu+Uno - Vu+Ultimo4K - Vu+ Zero - Vu+Solo-SE (In Black Evo ) - PrismCube