Hello Guest, if you are reading this it means you have not registered yet. Please take a second, Click here to register, and in a few simple steps you will be able to enjoy our community and use our OpenViX support section.
Page 1 of 3 123 LastLast
Results 1 to 15 of 41

Thread: Probleem met kanaal zoeken

  1. #1

    Title
    Junior Member
    Join Date
    May 2017
    Location
    Sweden
    Posts
    17
    Thanks
    11
    Thanked 6 Times in 5 Posts

    Probleem met kanaal zoeken

    Hallo,

    Ik heb een paar dagen geleden mijn VU+ Solo2 met "Openvix 6 3 007 Release Vusolo2 Usb" geflashed. Alles werkt uitstekend, maar wanneer ik kanalen ga scannen (1 LNB, gericht op Hotbird 13B/13C/13E) dan vindt mijn Solo2 slecht 23 kanaler. Na wat zoeken kwam ik tot de conclusie dat hij maar één transponder afzoekt. Als ik een blind scan doe dan vindt hij 4 transponders, maar de gevonden kanalen horen allemaal tot dezelfde transponder (zie beelden).

    Ik heb van alles uitgeprobeerd, maar welke instellingen ik ook verander, ik krijg steeds hetzelfde resultaat.

    Is hier iemand die licht kan werpen op dit probleem?

    Bij voorbaat dank,

    Edsel
    (Nederlander in Zweden)
    Attached Images Attached Images

  2. #2

    Title
    Senior Member
    Join Date
    Dec 2015
    Location
    Switzerland
    Posts
    315
    Thanks
    65
    Thanked 54 Times in 44 Posts
    When I do a manual scan I select Type of Scan Single satellite and define the satellite.
    Question 1: Have you attached the LNB coax cable to Tuner B?

    Can you try with my settings if you get more

    vuplus_manual_scan_single_satellite.jpg
    VU+ Solo2
    USB 32GB used as HDD
    Diseq 13.0E 19.0E

  3. The Following User Says Thank You to nekrub2 For This Useful Post:

    edsel (29-04-23)

  4. #3

    Title
    Junior Member
    Join Date
    May 2017
    Location
    Sweden
    Posts
    17
    Thanks
    11
    Thanked 6 Times in 5 Posts
    Hallo Nekrub2,

    Bedankt voor je antwoord.
    Ik heb zowel LNB A als LNB B geprobeerd.
    Ook jouw instellingen heb ik geprobeerd, single satellite, enz. Maar ze geven allemaal hetzelfde resultaat.

  5. #4

    Title
    Senior Member
    Join Date
    Dec 2015
    Location
    Switzerland
    Posts
    315
    Thanks
    65
    Thanked 54 Times in 44 Posts
    Can you check the signal quality SNR on one of the found stations.
    Setup > Tunters & Scanning > Signal Finder.

    If the SNR is low (50% or below) I would try adjusting the dish. I get for my stations 85 - 95% . After adjusting your dish you can do a second scan.

    Good luck
    VU+ Solo2
    USB 32GB used as HDD
    Diseq 13.0E 19.0E

  6. #5

    Title
    Senior Member
    Join Date
    Dec 2015
    Location
    Switzerland
    Posts
    315
    Thanks
    65
    Thanked 54 Times in 44 Posts
    What stations can your receive? I noticed that they are all HD and having checked them on Lyngsat Hotbird I did not find these frequencies. Could it be that you direct to another sat nearby?
    VU+ Solo2
    USB 32GB used as HDD
    Diseq 13.0E 19.0E

  7. #6

    Title
    Junior Member
    Join Date
    May 2017
    Location
    Sweden
    Posts
    17
    Thanks
    11
    Thanked 6 Times in 5 Posts
    Hi,

    The SNR is around 80%, but only for one (1) responder. All the other frequences are zero.

    2023-04-30 15.32.25.jpg

  8. #7

    Title
    Junior Member
    Join Date
    May 2017
    Location
    Sweden
    Posts
    17
    Thanks
    11
    Thanked 6 Times in 5 Posts
    These are the stations on the website of lyngsat:

    Screen Shot 04-30-23 at 04.26 PM.jpg

  9. #8

    Title
    Senior Member
    Join Date
    Dec 2015
    Location
    Switzerland
    Posts
    315
    Thanks
    65
    Thanked 54 Times in 44 Posts
    From your setup picture I see that you have setup Tuner A. You confirmed that you have plugged in you coax cable to Tuner B.
    You should set up Tuner A to loop-through and Tuner B to
    Configuration Mode Simple
    Mode Single
    Satellite "automatic"

    I cannot give you a screenshot as I have a twin head and a diseq to switch between astra 19.0 and hotbird 13.0. I just refer to the openvix manual.
    Hope this helps.
    VU+ Solo2
    USB 32GB used as HDD
    Diseq 13.0E 19.0E

  10. The Following User Says Thank You to nekrub2 For This Useful Post:

    edsel (01-05-23)

  11. #9

    Title
    Junior Member
    Join Date
    May 2017
    Location
    Sweden
    Posts
    17
    Thanks
    11
    Thanked 6 Times in 5 Posts
    Thank you for your support, nekrub2!


    I made the settings you asked for, but Satellite "automatic" did not work for me: It scanned a few satellites and returned with Satellite: "not configured"
    Then I chose Satellite: "Hotbird" instead and did the automatic channelscan and it returned only the 23 same channels.

    Before I opened my thread here on the forum I had moved the Coax cable to Tuner B since nothing worked. It was a last try to see if the problem depended on the A Tuner. But it shows the same problem and only finds these 23 channels.
    So Now I have put the system back as it initially was:
    Coax cable on Tuner A
    Tuner A on Mode: simple, Mode Single and Satellite: Hotbird
    Tuner B on "Equal to tuner A" (I guess this is the same as "loop-through" since that choice did not exist)

    With these settings I made a "Blind Scan" and it returned with the 23 channels again.

    2023-05-01 12.34.25.jpg2023-05-01 12.35.09.jpg2023-05-01 12.36.07.jpg

  12. #10

    Title
    Senior Member
    Join Date
    Dec 2015
    Location
    Switzerland
    Posts
    315
    Thanks
    65
    Thanked 54 Times in 44 Posts
    There is a similar thread in the VU+ Solo2 forum

    https://www.world-of-satellite.com/s...tellite-config

    The moderator Abu Baniaz suggested as I did. Maybe you contact him via PM and send him a link of this thread. I wouldn't know what else I could suggest you.
    VU+ Solo2
    USB 32GB used as HDD
    Diseq 13.0E 19.0E

  13. The Following User Says Thank You to nekrub2 For This Useful Post:

    edsel (01-05-23)

  14. #11

    Title
    Junior Member
    Join Date
    May 2017
    Location
    Sweden
    Posts
    17
    Thanks
    11
    Thanked 6 Times in 5 Posts
    Thank you, nekrub2!
    I think I will start a new thread in that subforum.
    But it can also be something wrong with my equipment.

  15. #12
    abu baniaz's Avatar
    Title
    Moderator
    Join Date
    Sep 2010
    Location
    East London
    Posts
    23,541
    Thanks
    6,517
    Thanked 9,224 Times in 6,287 Posts
    Can you translate the first few posts please?

  16. #13
    Joe_90's Avatar
    Title
    Moderator
    Join Date
    Mar 2014
    Location
    Wicklow, Ireland
    Posts
    4,244
    Thanks
    1,315
    Thanked 1,148 Times in 908 Posts
    @abu - from google translate (it's very useful!)

    post #1

    Channel search problem

    Hello,

    A few days ago I flashed my VU+ Solo2 with "Openvix 6 3 007 Release Vusolo2 Usb". Everything works great, but when I start scanning channels (1 LNB, aimed at Hotbird 13B/13C/13E) my Solo2 only finds 23 channels. After some searching I came to the conclusion that it only scans one transponder. When I do a blind scan, it finds 4 transponders, but the channels found all belong to the same transponder (see images).

    I've tried everything, but no matter what settings I change, I always get the same result.

    Is there anyone here who can shed light on this problem?

    Thank you in advance,

    Edsel
    (Dutchman in Sweden)
    GB Quad Plus, Mut@nt HD51, AX HD61, 80cm dish and Supreme Dark motor. Sony TA-AN1000, Sony UBP-X800M2 Bluray, Odroid N2+ (CoreElec), Monitor Audio Bronze 5.1 speakers

  17. The Following 2 Users Say Thank You to Joe_90 For This Useful Post:

    abu baniaz (01-05-23),edsel (02-05-23)

  18. #14
    Joe_90's Avatar
    Title
    Moderator
    Join Date
    Mar 2014
    Location
    Wicklow, Ireland
    Posts
    4,244
    Thanks
    1,315
    Thanked 1,148 Times in 908 Posts
    Post #3

    Hello Nekrub2,

    Thanks for your reply.
    I have tried both LNB A and LNB B.
    I also tried your settings, single satellite, etc. But they all give the same result.
    Last edited by Joe_90; 01-05-23 at 22:19.
    GB Quad Plus, Mut@nt HD51, AX HD61, 80cm dish and Supreme Dark motor. Sony TA-AN1000, Sony UBP-X800M2 Bluray, Odroid N2+ (CoreElec), Monitor Audio Bronze 5.1 speakers

  19. The Following 2 Users Say Thank You to Joe_90 For This Useful Post:

    abu baniaz (01-05-23),edsel (02-05-23)

  20. #15
    Joe_90's Avatar
    Title
    Moderator
    Join Date
    Mar 2014
    Location
    Wicklow, Ireland
    Posts
    4,244
    Thanks
    1,315
    Thanked 1,148 Times in 908 Posts
    Now - Hotbird at 13E should return 1000's (well at least 1,000) channels if you are scanning the entire satellite constellation, so getting only 23 channels would indicate that only one transponder is being scanned. @edsel - are you sure that you are scanning the entire satellite and not just one transponder?
    GB Quad Plus, Mut@nt HD51, AX HD61, 80cm dish and Supreme Dark motor. Sony TA-AN1000, Sony UBP-X800M2 Bluray, Odroid N2+ (CoreElec), Monitor Audio Bronze 5.1 speakers

Page 1 of 3 123 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
This website uses cookies
We use cookies to store session information to facilitate remembering your login information, to allow you to save website preferences, to personalise content and ads, to provide social media features and to analyse our traffic. We also share information about your use of our site with our social media, advertising and analytics partners.