do you have 4 cables attached to the tuners ?
do you have 4 cables attached to the tuners ?
VU+ DUO2 quad tuner with HDD 1 TB + Latest Openvix and VU+ DUO2 FB tuner + Octagon SF8008 FB tuner
Triax 88 cm rotor single LNB 30 E- 40 W
1 Gibertini 1.00 m fixed - 3 quad LNB 19E-23.5E-28.2E
yes pal i do all off fixed dishes
strange then because on my duo2 only a tuner is used when my slave box is on.In standby no tuner is used on main box. I have nearly the same config as yours with 2 dual tuners in main box an no tuners in 2 slave boxes.Those are connecthing by fall back tuner setup ( IPADRESS) to main box.So watching 2 differant channels in differant transponders on same sat is working fine.
VU+ DUO2 quad tuner with HDD 1 TB + Latest Openvix and VU+ DUO2 FB tuner + Octagon SF8008 FB tuner
Triax 88 cm rotor single LNB 30 E- 40 W
1 Gibertini 1.00 m fixed - 3 quad LNB 19E-23.5E-28.2E
i put it back to the way it was before and put tuner d at 28.2 degrees , signal sttength at near 100 percent but it will still not show the channels. i have tried a re=flash, think i am going to send the dual tuner back and go back to how it was before, very puzzling unless the tuner is faulty.
...maybe try the dual tuner with just one single tuner to see if you can get it working.
Desabled tuner b and still nothing but thanks anyway
sure you got the right tuner : Tuner VU+ Advanced Pluggable DVB-S2 .There are also dual tuners for duo2 and uno as well.
VU+ DUO2 quad tuner with HDD 1 TB + Latest Openvix and VU+ DUO2 FB tuner + Octagon SF8008 FB tuner
Triax 88 cm rotor single LNB 30 E- 40 W
1 Gibertini 1.00 m fixed - 3 quad LNB 19E-23.5E-28.2E
Twin must be in slot 3...….
Originally Posted by WOS
Yes in slot 3 exactly as the website states and it also states it works in a vu ultimo. It is blue and not green.
what version of image are you on ? In the past there where issues with some images not working the tuner perfectly due to driver problems.Found by google.
VU+ DUO2 quad tuner with HDD 1 TB + Latest Openvix and VU+ DUO2 FB tuner + Octagon SF8008 FB tuner
Triax 88 cm rotor single LNB 30 E- 40 W
1 Gibertini 1.00 m fixed - 3 quad LNB 19E-23.5E-28.2E
loopy123 (27-11-18)
Do you think that I got wIMG_20181124_161022.jpgwrong tuner
Twin tuner must be installed in Slot 3. You must also have single tuner modules installed to Slots 1 & 2 for the tuner to work correctly.
To test the tuner module Set BOTH Tuner C and D to Astra 28.2.
1) Connect a tested working satellite feed from Astra 28.2 to TOP input of the twin tuner module.
2) Menu > Setup > Tuner Config > Manual Scan > Select TUNER C AT TOP. Set 'Type of Scan' to 'Single Satellite', press ok to scan.
Once complete note the number of services found.
3) Now move the exact same cable to the BOTTOM INPUT of the twin tuner module.
4) Menu > Setup > Tuner Config > Manual Scan > Select TUNER D AT TOP. Set 'Type of Scan' to 'Single Satellite', press ok to scan.
If you find services on both tuners C & D then the issue lies elsewhere in your setup an NOT a faulty tuner.
If faulty WoS would exchange it for you without issue.
D I S C L A I M E R
My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!
Please help keep OpenViX online, donate HERE.
Rules can be found HERE
Support our sponsor World-Of-Satellite HERE
GIGABLUE UHD QUAD 4K, VU+ DUO 4K SE, ZGEMMA H7S, VU+ UNO 4K SE
Triax 1.1m Powered by TM2600, Fixed 28.2 Zone 2 dish with GT-SAT Unicable
no thats the right one
VU+ DUO2 quad tuner with HDD 1 TB + Latest Openvix and VU+ DUO2 FB tuner + Octagon SF8008 FB tuner
Triax 88 cm rotor single LNB 30 E- 40 W
1 Gibertini 1.00 m fixed - 3 quad LNB 19E-23.5E-28.2E
Please excuse my incorrect post about not using slot C.