Hello,
could you please share working and tested usb wifi adapters for Gigablue Quad Plus.
Many thanks
Hello,
could you please share working and tested usb wifi adapters for Gigablue Quad Plus.
Many thanks
The availability of drivers depends on the image, and not (or hardly) on the box in use.
So please tell us which image you are using.
Help asked via PM will be ignored.
The forum is there for help and all will benefit from your questions.
NO CARD SHARING TALK WILL BE TOLERATED, LAN OR WAN, IN OPEN FORUM OR PM !
English is not my native tongue.
I apologise for all my grammar, spelling and idiom errors.
There are too many on ebay for me to know if works and a lot of them don't say what chipset is inside.
Found one with this chipset "Ralink RT 5372" will this work?
Moved to this section.
Please read this thread HERE
I made this a 'sticky' as it may be useful for many.
Help asked via PM will be ignored.
The forum is there for help and all will benefit from your questions.
NO CARD SHARING TALK WILL BE TOLERATED, LAN OR WAN, IN OPEN FORUM OR PM !
English is not my native tongue.
I apologise for all my grammar, spelling and idiom errors.
I purchased this one
TP-LINK 300Mbps Mini Wireless N USB Adapter
Model No TL-WN823N
At a cost of £12.00 from a well known Supermarket
worked on VU Zero without the need to install any additional drivers other than what's included the VIX Apollo Image
Vu+UNO 4K SE [OE-Alliance-4.4 Firmware 5.4-010-Build Oscam-r11693-798][with keys]
Vu+DUO 2 [OE-Alliance-4.4 Firmware 5.4-003-Build Oscam-r11572-798][with keys]
Vu+SOLO 2 [OE-Alliance-4.3 Firmware 5.3-039-Build MGcamd]
Vu+SOLO SE [OE-Alliance-4.4 Firmware 5.4-003-Build MGcamd]
TP-Link TL-WR702N Universal N Nano Travel Router/Wi-Fi Range Extender/TV, Gaming Set-top Adapter with USB Charger".
Have gigablue openvix apollo 126, set up the device in "client mode" then plug the ethernet from nano router to receiver and it works perfectly.
Using it until i get a usb adapter.
Edimax EW-7711UAn used on vu+ duo and duo 2. works out of the box.
Yes. Would like to know if any AC adaptors work.
Octagon SF8008 4K, VU+Duo 2..
Edision OS MINI,
These are plug and play with all boxes with VIX image installed. LB-Link USB Wi-Fi Module with Antenna for Raspberry Pi Computer. It uses a RTl8192cu WiFi chip from Realtek.
I hope many excellent articles will be posted on your site. Thank you very much for this and continue to share.
Hi,
this thread was not filled with enough information so I add some.
I have working with OpenVix now
TP-Link WN722N (out of the box) and
TP-Link WN822N V4 (after installing RTL8192EU driver)
ciao
---
Sat:VU+ Ultimo4K/Solo4K/Duo2/2*Solo2/Ultimo
Remote: Harmony 200, 700, Link, Smart Control, Smart Companion, Elite, 2*Ultimate, Keyboard
The TP-Link WN823N V2 works perfectly with the RTL8192EU driver.
TP-Link WN727N works out of the box
Zgemma H7S running OpenVIX 6.2, Darkmotor, Triax TD110 dish, Inverto Black Ultra dual lnb
LG 50UM7450 4K TV, Pioneer VSX-534 Atmos AVR , Panasonic UB820 region free 4K Bluray & a PS4.
The Edimax EW-7811Un (V1.0A) works out the box on the Xtrend ET8500 running OpenViX build 5.1.013.
Looking online, websites say the EW-781Un runs on a Realtek RTL8188CU chipset, but on my receiver it seems to be working with the Realtek RTL8192CU driver. I'm not sure if the EU and US models run on different chipsets, and if my EU does in fact have a RTL8192CU chipset, while the US models have a RTL8188CU chipset, but it's the only reason I can think of for the discrepancy.