Hello Guest, if you are reading this it means you have not registered yet. Please take a second, Click here to register, and in a few simple steps you will be able to enjoy our community and use our OpenViX support section.
Results 1 to 7 of 7

Thread: Monoblock Tuner configuration

  1. #1
    afterburn's Avatar
    Title
    Forum Supporter
    Donated Member
    Join Date
    Aug 2014
    Posts
    259
    Thanks
    138
    Thanked 29 Times in 18 Posts

    Monoblock Tuner configuration

    I have purchased a monoblock lnb in order to receive 19.2 and 23.5. I am looking for some help with the settings here. Any help appreciated.

  2. #2
    abu baniaz's Avatar
    Title
    Moderator
    Join Date
    Sep 2010
    Location
    East London
    Posts
    23,541
    Thanks
    6,517
    Thanked 9,224 Times in 6,287 Posts
    Simple
    Diseqc A/B
    Port A Automatic
    Port B Automatic

  3. The Following User Says Thank You to abu baniaz For This Useful Post:

    afterburn (18-06-17)

  4. #3
    afterburn's Avatar
    Title
    Forum Supporter
    Donated Member
    Join Date
    Aug 2014
    Posts
    259
    Thanks
    138
    Thanked 29 Times in 18 Posts
    Is that all I have to do. Do I need to specify the satellites ? the bottom 2 values are as follows
    Set voltage and 22KHz yes
    Send DISeqC only on satellite change No

    Are these correct?

  5. #4
    abu baniaz's Avatar
    Title
    Moderator
    Join Date
    Sep 2010
    Location
    East London
    Posts
    23,541
    Thanks
    6,517
    Thanked 9,224 Times in 6,287 Posts
    Leave the other options as they are.

  6. The Following User Says Thank You to abu baniaz For This Useful Post:

    afterburn (18-06-17)

  7. #5
    afterburn's Avatar
    Title
    Forum Supporter
    Donated Member
    Join Date
    Aug 2014
    Posts
    259
    Thanks
    138
    Thanked 29 Times in 18 Posts
    I'm trying this on an 80cm dish using a 4.3 degree monoblock. Any Experience of this abu? Difficult or not would you say?

  8. #6
    abu baniaz's Avatar
    Title
    Moderator
    Join Date
    Sep 2010
    Location
    East London
    Posts
    23,541
    Thanks
    6,517
    Thanked 9,224 Times in 6,287 Posts
    A monoblock LNB in essence is just two LNBs in one housing and a built-in diseqc switch. It will work, but dishes have different sizes, so it is impossible to tweak adjustment properly because they are one block. I have only ever used a monoblock for 13/19. Provided the dish is aligned properly, it is easy. Just clamp the correct LNB. Your response in the other thread shows a good understanding of the principles of multi-LNB setup.

  9. The Following User Says Thank You to abu baniaz For This Useful Post:

    afterburn (19-06-17)

  10. #7
    afterburn's Avatar
    Title
    Forum Supporter
    Donated Member
    Join Date
    Aug 2014
    Posts
    259
    Thanks
    138
    Thanked 29 Times in 18 Posts
    Thanks abu. Set this up today and worked fine. I have a perfectly acceptable single on both 19.2 and 23.5 (about 75%) so job done.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
This website uses cookies
We use cookies to store session information to facilitate remembering your login information, to allow you to save website preferences, to personalise content and ads, to provide social media features and to analyse our traffic. We also share information about your use of our site with our social media, advertising and analytics partners.