Hi Andy, thanks very much for your quick reply.
Yes I did that and every time I try to attach the file, a red mark appear beside the file name and show fail to attach.
In fact I am doing it now still cannot attach any file.
Hi Andy, thanks very much for your quick reply.
Yes I did that and every time I try to attach the file, a red mark appear beside the file name and show fail to attach.
In fact I am doing it now still cannot attach any file.
Try attaching the file twice (ie 2 files selected) , the second one should work ok.
bumperbee (22-05-17)
You add images using the square icon with a dot in each corner (to the right of the globe with a red cross on it) rather than uploading them.
Although you could always zip them and upload that....
Attaching a zip file needs Advanced mode, adding a picture doesn't. (Don't ask me why as I have no idea).
However, what I really need to see is what happens when you put a USB stick into the running ET10k.
Last edited by birdman; 22-05-17 at 14:06.
MiracleBox Prem Twin HD - 2@DVB-T2 + Xtrend et8000 - 5(incl. 2 different USBs)@DVB-T2[terrestrial - UK Freeview HD, Sandy Heath] - LAN/USB-stick/HDD
bumperbee (22-05-17)
I just tried adding the file twice, it didn’t work. Using the “add image” also didn’t work. I can only append below the content of dmesg by inserting a flashdrive.
[ 0.055000] Key type id_resolver registered
[ 0.055000] Key type id_legacy registered
[ 0.055000] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.055000] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 0.055000] fuse init (API version 7.26)
[ 0.061000] bounce: pool size: 64 pages
[ 0.061000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.061000] io scheduler noop registered
[ 0.061000] io scheduler cfq registered (default)
[ 0.061000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.062000] serial8250.0: ttyS0 at MMIO 0x10406b00 (irq = 62, base_baud = 5062500) is a 16550A
[ 0.063000] serial8250.0: ttyS1 at MMIO 0x10406b40 (irq = 63, base_baud = 5062500) is a 16550A
[ 0.063000] serial8250.0: ttyS2 at MMIO 0x10406b80 (irq = 64, base_baud = 5062500) is a 16550A
[ 0.070000] loop: module loaded
[ 0.070000] ahci ahci.0: SSS flag set, parallel bus scan disabled
[ 0.080000] ahci ahci.0: AHCI 0001.0300 32 slots 2 ports 6 Gbps 0x3 impl platform mode
[ 0.080000] ahci ahci.0: flags: ncq sntf stag clo slum part
[ 0.084000] scsi host0: ahci
[ 0.085000] scsi host1: ahci
[ 0.085000] ata1: FORCE: PHY spd limit set to 3.0Gbps
[ 0.085000] ata1: SATA max UDMA/133 mmio [mem 0x10181000-0x10190fff] port 0x100 irq 42
[ 0.085000] ata2: FORCE: PHY spd limit set to 3.0Gbps
[ 0.085000] ata2: SATA max UDMA/133 mmio [mem 0x10181000-0x10190fff] port 0x180 irq 42
[ 0.085000] brcmstb_nand: NAND controller driver is loaded
[ 0.086000] libphy: Fixed MDIO Bus: probed
[ 0.086000] __clk_enable: network [1]
[ 0.086000] bcm7425_pm_network_enable 00
[ 0.086000] __clk_enable: enet [1]
[ 0.086000] bcm40nm_pm_genet_enable 00
[ 0.198000] bcmgenet: configuring instance #0 for internal PHY
[ 0.220000] bcmgenet bcmgenet.0 eth0: link down
[ 0.220000] __clk_disable: enet [0]
[ 0.220000] bcm40nm_pm_genet_disable 00
[ 0.220000] __clk_disable: network [0]
[ 0.220000] bcm7425_pm_network_disable 00
[ 0.220000] __clk_enable: network [1]
[ 0.220000] bcm7425_pm_network_enable 00
[ 0.220000] __clk_enable: moca_genet [1]
[ 0.220000] bcm40nm_pm_genet1_enable 00
[ 0.220000] __clk_enable: moca [1]
[ 0.220000] bcm40nm_pm_moca_enable 00
[ 0.233000] Found PHY at Address 31
[ 0.233000] bcmgenet: configuring instance #1 for external RGMII
[ 0.233000] __clk_disable: moca [0]
[ 0.233000] bcm40nm_pm_moca_disable 00
[ 0.233000] __clk_disable: moca_genet [0]
[ 0.233000] bcm40nm_pm_genet1_disable 00
[ 0.233000] __clk_disable: network [0]
[ 0.233000] bcm7425_pm_network_disable 00
[ 0.233000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.233000] __clk_enable: usb [1]
[ 0.233000] bcm40nm_pm_usb_enable 00
[ 0.233000] ehci-brcm ehci-brcm.0: Broadcom STB EHCI
[ 0.233000] ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1
[ 0.243000] ehci-brcm ehci-brcm.0: irq 66, io mem 0x10480300
[ 0.250000] ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
[ 0.250000] hub 1-0:1.0: USB hub found
[ 0.250000] hub 1-0:1.0: 1 port detected
[ 0.250000] ehci-brcm ehci-brcm.1: Broadcom STB EHCI
[ 0.250000] ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus number 2
[ 0.261000] ehci-brcm ehci-brcm.1: irq 67, io mem 0x10480500
[ 0.268000] ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00
[ 0.268000] hub 2-0:1.0: USB hub found
[ 0.268000] hub 2-0:1.0: 1 port detected
[ 0.268000] ehci-brcm ehci-brcm.2: Broadcom STB EHCI
[ 0.268000] ehci-brcm ehci-brcm.2: new USB bus registered, assigned bus number 3
[ 0.279000] ehci-brcm ehci-brcm.2: irq 71, io mem 0x10490300
[ 0.286000] ehci-brcm ehci-brcm.2: USB 0.0 started, EHCI 1.00
[ 0.286000] hub 3-0:1.0: USB hub found
[ 0.286000] hub 3-0:1.0: 1 port detected
[ 0.286000] ehci-brcm ehci-brcm.3: Broadcom STB EHCI
[ 0.286000] ehci-brcm ehci-brcm.3: new USB bus registered, assigned bus number 4
[ 0.297000] ehci-brcm ehci-brcm.3: irq 72, io mem 0x10490500
[ 0.304000] ehci-brcm ehci-brcm.3: USB 0.0 started, EHCI 1.00
[ 0.304000] hub 4-0:1.0: USB hub found
[ 0.304000] hub 4-0:1.0: 1 port detected
[ 0.304000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.304000] ohci-brcm ohci-brcm.0: Broadcom STB OHCI
[ 0.305000] ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 5
[ 0.305000] ohci-brcm ohci-brcm.0: irq 68, io mem 0x10480400
[ 0.371000] hub 5-0:1.0: USB hub found
[ 0.371000] hub 5-0:1.0: 1 port detected
[ 0.371000] ohci-brcm ohci-brcm.1: Broadcom STB OHCI
[ 0.371000] ohci-brcm ohci-brcm.1: new USB bus registered, assigned bus number 6
[ 0.372000] ohci-brcm ohci-brcm.1: irq 69, io mem 0x10480600
[ 0.397000] ata1: SATA link down (SStatus 0 SControl 320)
[ 0.407000] ata1: exception Emask 0x10 SAct 0x0 SErr 0x4000000 action 0xe frozen
[ 0.407000] ata1: irq_stat 0x00000040, connection status changed
[ 0.407000] ata1: SError: { DevExch }
[ 0.407000] ata1: hard resetting link
[ 0.438000] hub 6-0:1.0: USB hub found
[ 0.438000] hub 6-0:1.0: 1 port detected
[ 0.438000] ohci-brcm ohci-brcm.2: Broadcom STB OHCI
[ 0.438000] ohci-brcm ohci-brcm.2: new USB bus registered, assigned bus number 7
[ 0.439000] ohci-brcm ohci-brcm.2: irq 73, io mem 0x10490400
[ 0.505000] hub 7-0:1.0: USB hub found
[ 0.505000] hub 7-0:1.0: 1 port detected
[ 0.505000] ohci-brcm ohci-brcm.3: Broadcom STB OHCI
[ 0.505000] ohci-brcm ohci-brcm.3: new USB bus registered, assigned bus number 8
[ 0.506000] ohci-brcm ohci-brcm.3: irq 74, io mem 0x10490600
[ 0.572000] hub 8-0:1.0: USB hub found
[ 0.572000] hub 8-0:1.0: 1 port detected
[ 0.573000] usbcore: registered new interface driver usb-storage
[ 0.573000] mousedev: PS/2 mouse device common for all mice
[ 0.573000] i2c /dev entries driver
[ 0.573000] usbcore: registered new interface driver btusb
[ 0.573000] hidraw: raw HID events driver (C) Jiri Kosina
[ 0.573000] usbcore: registered new interface driver usbhid
[ 0.573000] usbhid: USB HID core driver
[ 0.574000] NET: Registered protocol family 17
[ 0.574000] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 0.574000] Bluetooth: HIDP socket layer initialized
[ 0.574000] Key type dns_resolver registered
[ 0.574000] PM: CP0 COUNT/COMPARE frequency does not depend on divisor
[ 0.575000] EBI CS1: setting up NAND flash (primary)
[ 0.575000] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xd3
[ 0.575000] nand: Samsung NAND 1GiB 3,3V 8-bit
[ 0.575000] nand: 1024 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 0.575000] brcmnand brcmnand.0: 1024MiB total, 128KiB blocks, 2KiB pages, 16B OOB, 8-bit, BCH-16 (1KiB sector)
[ 0.576000] Bad block table found at page 524224, version 0x01
[ 0.576000] Bad block table found at page 524160, version 0x01
[ 0.576000] nand_read_bbt: bad block at 0x00002f080000
[ 0.576000] nand_read_bbt: bad block at 0x000032740000
[ 0.577000] Creating 3 MTD partitions on "brcmnand.0":
[ 0.577000] 0x000000000000-0x000040000000 : "complete"
[ 0.583000] 0x000000000000-0x000000600000 : "kernel"
[ 0.584000] 0x000000600000-0x000040000000 : "rootfs"
[ 0.590000] EBI CS0: setting up SPI flash
[ 0.590000] brcm_setup_spi_flash: can't locate SPI master
[ 0.590000] brcm_setup_cs: can't register SPI flash (error -19)
[ 0.591000] ubi0: default fastmap pool size: 256
[ 0.591000] ubi0: default fastmap WL pool size: 128
[ 0.591000] ubi0: attaching mtd2
[ 0.600000] usb 3-1: new high-speed USB device number 2 using ehci-brcm
[ 0.702000] ata2: SATA link down (SStatus 0 SControl 320)
[ 0.719000] hub 3-1:1.0: USB hub found
[ 0.719000] hub 3-1:1.0: 4 ports detected
[ 0.911000] ubi0: attached by fastmap
[ 0.911000] ubi0: fastmap pool size: 256
[ 0.911000] ubi0: fastmap WL pool size: 128
[ 0.927000] ubi0: attached mtd2 (name "rootfs", size 1018 MiB)
[ 0.927000] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 0.927000] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 0.927000] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 0.927000] ubi0: good PEBs: 8138, bad PEBs: 6, corrupted PEBs: 0
[ 0.927000] ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 0.927000] ubi0: max/mean erase counter: 3/0, WL threshold: 4096, image sequence number: 2074121938
[ 0.927000] ubi0: available PEBs: 0, total reserved PEBs: 8138, PEBs reserved for bad PEB handling: 154
[ 0.927000] ubi0: background thread "ubi_bgt0d" started, PID 82
[ 0.927000] ALSA device list:
[ 0.927000] No soundcards found.
[ 0.927000] Warning: unable to open an initial console.
[ 0.928000] UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 83
[ 1.004000] usb 3-1.1: new full-speed USB device number 3 using ehci-brcm
[ 1.051000] UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[ 1.051000] UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 1.051000] UBIFS (ubi0:0): FS size: 1011617792 bytes (964 MiB, 7967 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[ 1.051000] UBIFS (ubi0:0): reserved for root: 0 bytes (0 KiB)
[ 1.051000] UBIFS (ubi0:0): media format: w4/r0 (latest is w5/r0), UUID 570219F0-4287-4767-BDC6-42567E1E8A09, small LPT model
[ 1.063000] VFS: Mounted root (ubifs filesystem) on device 0:12.
[ 1.075000] devtmpfs: mounted
[ 1.076000] Freeing unused kernel memory: 288K
[ 1.076000] This architecture does not have kernel memory protection.
[ 1.177000] usb 3-1.3: new high-speed USB device number 4 using ehci-brcm
[ 1.383000] random: crng init done
[ 6.145000] ata1: link is slow to respond, please be patient (ready=0)
[ 7.140000] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
[ 7.313000] ata1.00: ATA-9: WDC WD3003FZEX-00Z4SA0, 01.01A01, max UDMA/133
[ 7.313000] ata1.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 7.313000] ata1.00: configured for UDMA/133
[ 7.313000] ata1: EH complete
[ 7.314000] scsi 0:0:0:0: Direct-Access ATA WDC WD3003FZEX-0 1A01 PQ: 0 ANSI: 5
[ 7.328000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 7.328000] sd 0:0:0:0: [sda] 5860533168 512-byte logical blocks: (3.00 TB/2.73 TiB)
[ 7.328000] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 7.328000] sd 0:0:0:0: [sda] Write Protect is off
[ 7.329000] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 7.329000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 7.376000] sda: sda1
[ 7.377000] sd 0:0:0:0: [sda] Attached SCSI disk
[ 7.394000] tpm: loading out-of-tree module taints kernel.
[ 7.395000] usbcore: registered new interface driver tpm
[ 8.375000] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 10.710000] dvb: module_layout: kernel tainted.
[ 10.710000] Disabling lock debugging due to kernel taint
[ 14.792000] input: dreambox remote control (native) as /devices/virtual/input/input0
[ 14.796000] input: dreambox advanced remote control (native) as /devices/virtual/input/input1
[ 14.835000] dvbdev: DVB: registering new adapter (dvb0)
[ 14.836000] platform dvb0.0: DVB: registering adapter 0 frontend 0 (DVB-C)...
[ 14.837000] platform dvb0.0: DVB: registering adapter 0 frontend 1 (DVB-C)...
[ 14.840000] platform dvb0.0: DVB: registering adapter 0 frontend 2 (DVB-C)...
[ 14.841000] platform dvb0.0: DVB: registering adapter 0 frontend 3 (DVB-C)...
[ 15.180000] input: front panel as /devices/virtual/input/input2
[ 16.013000] Registered IR keymap rc-cec
[ 16.013000] input: RC for hdmi_cec as /devices/platform/hdmi.0/rc/rc0/input3
[ 16.014000] rc rc0: RC for hdmi_cec as /devices/platform/hdmi.0/rc/rc0
[ 16.259000] SGI XFS with security attributes, realtime, no debug enabled
[ 16.583000] r8712u: module is from the staging directory, the quality is unknown, you have been warned.
[ 16.585000] r8712u: register rtl8712_netdev_ops to netdev_ops
[ 16.585000] usb 3-1.3: r8712u: USB_SPEED_HIGH with 4 endpoints
[ 16.586000] usb 3-1.3: r8712u: Boot from EFUSE: Autoload OK
[ 17.308000] usb 3-1.3: r8712u: CustomerID = 0x000a
[ 17.308000] usb 3-1.3: r8712u: MAC Address from efuse = 00:87:23:82:a1:16
[ 17.308000] usb 3-1.3: r8712u: Loading firmware from "rtlwifi/rtl8712u.bin"
[ 17.308000] usbcore: registered new interface driver r8712u
This time is by inserting the 5Tb Hdd.
[ 0.055000] Key type id_resolver registered
[ 0.055000] Key type id_legacy registered
[ 0.055000] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.055000] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 0.055000] fuse init (API version 7.26)
[ 0.061000] bounce: pool size: 64 pages
[ 0.061000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.061000] io scheduler noop registered
[ 0.061000] io scheduler cfq registered (default)
[ 0.061000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.062000] serial8250.0: ttyS0 at MMIO 0x10406b00 (irq = 62, base_baud = 5062500) is a 16550A
[ 0.063000] serial8250.0: ttyS1 at MMIO 0x10406b40 (irq = 63, base_baud = 5062500) is a 16550A
[ 0.063000] serial8250.0: ttyS2 at MMIO 0x10406b80 (irq = 64, base_baud = 5062500) is a 16550A
[ 0.070000] loop: module loaded
[ 0.070000] ahci ahci.0: SSS flag set, parallel bus scan disabled
[ 0.080000] ahci ahci.0: AHCI 0001.0300 32 slots 2 ports 6 Gbps 0x3 impl platform mode
[ 0.080000] ahci ahci.0: flags: ncq sntf stag clo slum part
[ 0.084000] scsi host0: ahci
[ 0.085000] scsi host1: ahci
[ 0.085000] ata1: FORCE: PHY spd limit set to 3.0Gbps
[ 0.085000] ata1: SATA max UDMA/133 mmio [mem 0x10181000-0x10190fff] port 0x100 irq 42
[ 0.085000] ata2: FORCE: PHY spd limit set to 3.0Gbps
[ 0.085000] ata2: SATA max UDMA/133 mmio [mem 0x10181000-0x10190fff] port 0x180 irq 42
[ 0.085000] brcmstb_nand: NAND controller driver is loaded
[ 0.086000] libphy: Fixed MDIO Bus: probed
[ 0.086000] __clk_enable: network [1]
[ 0.086000] bcm7425_pm_network_enable 00
[ 0.086000] __clk_enable: enet [1]
[ 0.086000] bcm40nm_pm_genet_enable 00
[ 0.198000] bcmgenet: configuring instance #0 for internal PHY
[ 0.220000] bcmgenet bcmgenet.0 eth0: link down
[ 0.220000] __clk_disable: enet [0]
[ 0.220000] bcm40nm_pm_genet_disable 00
[ 0.220000] __clk_disable: network [0]
[ 0.220000] bcm7425_pm_network_disable 00
[ 0.220000] __clk_enable: network [1]
[ 0.220000] bcm7425_pm_network_enable 00
[ 0.220000] __clk_enable: moca_genet [1]
[ 0.220000] bcm40nm_pm_genet1_enable 00
[ 0.220000] __clk_enable: moca [1]
[ 0.220000] bcm40nm_pm_moca_enable 00
[ 0.233000] Found PHY at Address 31
[ 0.233000] bcmgenet: configuring instance #1 for external RGMII
[ 0.233000] __clk_disable: moca [0]
[ 0.233000] bcm40nm_pm_moca_disable 00
[ 0.233000] __clk_disable: moca_genet [0]
[ 0.233000] bcm40nm_pm_genet1_disable 00
[ 0.233000] __clk_disable: network [0]
[ 0.233000] bcm7425_pm_network_disable 00
[ 0.233000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.233000] __clk_enable: usb [1]
[ 0.233000] bcm40nm_pm_usb_enable 00
[ 0.233000] ehci-brcm ehci-brcm.0: Broadcom STB EHCI
[ 0.233000] ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1
[ 0.243000] ehci-brcm ehci-brcm.0: irq 66, io mem 0x10480300
[ 0.250000] ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
[ 0.250000] hub 1-0:1.0: USB hub found
[ 0.250000] hub 1-0:1.0: 1 port detected
[ 0.250000] ehci-brcm ehci-brcm.1: Broadcom STB EHCI
[ 0.250000] ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus number 2
[ 0.261000] ehci-brcm ehci-brcm.1: irq 67, io mem 0x10480500
[ 0.268000] ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00
[ 0.268000] hub 2-0:1.0: USB hub found
[ 0.268000] hub 2-0:1.0: 1 port detected
[ 0.268000] ehci-brcm ehci-brcm.2: Broadcom STB EHCI
[ 0.268000] ehci-brcm ehci-brcm.2: new USB bus registered, assigned bus number 3
[ 0.279000] ehci-brcm ehci-brcm.2: irq 71, io mem 0x10490300
[ 0.286000] ehci-brcm ehci-brcm.2: USB 0.0 started, EHCI 1.00
[ 0.286000] hub 3-0:1.0: USB hub found
[ 0.286000] hub 3-0:1.0: 1 port detected
[ 0.286000] ehci-brcm ehci-brcm.3: Broadcom STB EHCI
[ 0.286000] ehci-brcm ehci-brcm.3: new USB bus registered, assigned bus number 4
[ 0.297000] ehci-brcm ehci-brcm.3: irq 72, io mem 0x10490500
[ 0.304000] ehci-brcm ehci-brcm.3: USB 0.0 started, EHCI 1.00
[ 0.304000] hub 4-0:1.0: USB hub found
[ 0.304000] hub 4-0:1.0: 1 port detected
[ 0.304000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.304000] ohci-brcm ohci-brcm.0: Broadcom STB OHCI
[ 0.305000] ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 5
[ 0.305000] ohci-brcm ohci-brcm.0: irq 68, io mem 0x10480400
[ 0.371000] hub 5-0:1.0: USB hub found
[ 0.371000] hub 5-0:1.0: 1 port detected
[ 0.371000] ohci-brcm ohci-brcm.1: Broadcom STB OHCI
[ 0.371000] ohci-brcm ohci-brcm.1: new USB bus registered, assigned bus number 6
[ 0.372000] ohci-brcm ohci-brcm.1: irq 69, io mem 0x10480600
[ 0.397000] ata1: SATA link down (SStatus 0 SControl 320)
[ 0.407000] ata1: exception Emask 0x10 SAct 0x0 SErr 0x4000000 action 0xe frozen
[ 0.407000] ata1: irq_stat 0x00000040, connection status changed
[ 0.407000] ata1: SError: { DevExch }
[ 0.407000] ata1: hard resetting link
[ 0.438000] hub 6-0:1.0: USB hub found
[ 0.438000] hub 6-0:1.0: 1 port detected
[ 0.438000] ohci-brcm ohci-brcm.2: Broadcom STB OHCI
[ 0.438000] ohci-brcm ohci-brcm.2: new USB bus registered, assigned bus number 7
[ 0.439000] ohci-brcm ohci-brcm.2: irq 73, io mem 0x10490400
[ 0.505000] hub 7-0:1.0: USB hub found
[ 0.505000] hub 7-0:1.0: 1 port detected
[ 0.505000] ohci-brcm ohci-brcm.3: Broadcom STB OHCI
[ 0.505000] ohci-brcm ohci-brcm.3: new USB bus registered, assigned bus number 8
[ 0.506000] ohci-brcm ohci-brcm.3: irq 74, io mem 0x10490600
[ 0.572000] hub 8-0:1.0: USB hub found
[ 0.572000] hub 8-0:1.0: 1 port detected
[ 0.573000] usbcore: registered new interface driver usb-storage
[ 0.573000] mousedev: PS/2 mouse device common for all mice
[ 0.573000] i2c /dev entries driver
[ 0.573000] usbcore: registered new interface driver btusb
[ 0.573000] hidraw: raw HID events driver (C) Jiri Kosina
[ 0.573000] usbcore: registered new interface driver usbhid
[ 0.573000] usbhid: USB HID core driver
[ 0.574000] NET: Registered protocol family 17
[ 0.574000] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 0.574000] Bluetooth: HIDP socket layer initialized
[ 0.574000] Key type dns_resolver registered
[ 0.574000] PM: CP0 COUNT/COMPARE frequency does not depend on divisor
[ 0.575000] EBI CS1: setting up NAND flash (primary)
[ 0.575000] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xd3
[ 0.575000] nand: Samsung NAND 1GiB 3,3V 8-bit
[ 0.575000] nand: 1024 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 0.575000] brcmnand brcmnand.0: 1024MiB total, 128KiB blocks, 2KiB pages, 16B OOB, 8-bit, BCH-16 (1KiB sector)
[ 0.576000] Bad block table found at page 524224, version 0x01
[ 0.576000] Bad block table found at page 524160, version 0x01
[ 0.576000] nand_read_bbt: bad block at 0x00002f080000
[ 0.576000] nand_read_bbt: bad block at 0x000032740000
[ 0.577000] Creating 3 MTD partitions on "brcmnand.0":
[ 0.577000] 0x000000000000-0x000040000000 : "complete"
[ 0.583000] 0x000000000000-0x000000600000 : "kernel"
[ 0.584000] 0x000000600000-0x000040000000 : "rootfs"
[ 0.590000] EBI CS0: setting up SPI flash
[ 0.590000] brcm_setup_spi_flash: can't locate SPI master
[ 0.590000] brcm_setup_cs: can't register SPI flash (error -19)
[ 0.591000] ubi0: default fastmap pool size: 256
[ 0.591000] ubi0: default fastmap WL pool size: 128
[ 0.591000] ubi0: attaching mtd2
[ 0.600000] usb 3-1: new high-speed USB device number 2 using ehci-brcm
[ 0.702000] ata2: SATA link down (SStatus 0 SControl 320)
[ 0.719000] hub 3-1:1.0: USB hub found
[ 0.719000] hub 3-1:1.0: 4 ports detected
[ 0.911000] ubi0: attached by fastmap
[ 0.911000] ubi0: fastmap pool size: 256
[ 0.911000] ubi0: fastmap WL pool size: 128
[ 0.927000] ubi0: attached mtd2 (name "rootfs", size 1018 MiB)
[ 0.927000] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 0.927000] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 0.927000] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 0.927000] ubi0: good PEBs: 8138, bad PEBs: 6, corrupted PEBs: 0
[ 0.927000] ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 0.927000] ubi0: max/mean erase counter: 3/0, WL threshold: 4096, image sequence number: 2074121938
[ 0.927000] ubi0: available PEBs: 0, total reserved PEBs: 8138, PEBs reserved for bad PEB handling: 154
[ 0.927000] ubi0: background thread "ubi_bgt0d" started, PID 82
[ 0.927000] ALSA device list:
[ 0.927000] No soundcards found.
[ 0.927000] Warning: unable to open an initial console.
[ 0.928000] UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 83
[ 1.004000] usb 3-1.1: new full-speed USB device number 3 using ehci-brcm
[ 1.051000] UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[ 1.051000] UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 1.051000] UBIFS (ubi0:0): FS size: 1011617792 bytes (964 MiB, 7967 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[ 1.051000] UBIFS (ubi0:0): reserved for root: 0 bytes (0 KiB)
[ 1.051000] UBIFS (ubi0:0): media format: w4/r0 (latest is w5/r0), UUID 570219F0-4287-4767-BDC6-42567E1E8A09, small LPT model
[ 1.063000] VFS: Mounted root (ubifs filesystem) on device 0:12.
[ 1.075000] devtmpfs: mounted
[ 1.076000] Freeing unused kernel memory: 288K
[ 1.076000] This architecture does not have kernel memory protection.
[ 1.177000] usb 3-1.3: new high-speed USB device number 4 using ehci-brcm
[ 1.383000] random: crng init done
[ 6.145000] ata1: link is slow to respond, please be patient (ready=0)
[ 7.140000] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
[ 7.313000] ata1.00: ATA-9: WDC WD3003FZEX-00Z4SA0, 01.01A01, max UDMA/133
[ 7.313000] ata1.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 7.313000] ata1.00: configured for UDMA/133
[ 7.313000] ata1: EH complete
[ 7.314000] scsi 0:0:0:0: Direct-Access ATA WDC WD3003FZEX-0 1A01 PQ: 0 ANSI: 5
[ 7.328000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 7.328000] sd 0:0:0:0: [sda] 5860533168 512-byte logical blocks: (3.00 TB/2.73 TiB)
[ 7.328000] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 7.328000] sd 0:0:0:0: [sda] Write Protect is off
[ 7.329000] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 7.329000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 7.376000] sda: sda1
[ 7.377000] sd 0:0:0:0: [sda] Attached SCSI disk
[ 7.394000] tpm: loading out-of-tree module taints kernel.
[ 7.395000] usbcore: registered new interface driver tpm
[ 8.375000] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 10.710000] dvb: module_layout: kernel tainted.
[ 10.710000] Disabling lock debugging due to kernel taint
[ 14.792000] input: dreambox remote control (native) as /devices/virtual/input/input0
[ 14.796000] input: dreambox advanced remote control (native) as /devices/virtual/input/input1
[ 14.835000] dvbdev: DVB: registering new adapter (dvb0)
[ 14.836000] platform dvb0.0: DVB: registering adapter 0 frontend 0 (DVB-C)...
[ 14.837000] platform dvb0.0: DVB: registering adapter 0 frontend 1 (DVB-C)...
[ 14.840000] platform dvb0.0: DVB: registering adapter 0 frontend 2 (DVB-C)...
[ 14.841000] platform dvb0.0: DVB: registering adapter 0 frontend 3 (DVB-C)...
[ 15.180000] input: front panel as /devices/virtual/input/input2
[ 16.013000] Registered IR keymap rc-cec
[ 16.013000] input: RC for hdmi_cec as /devices/platform/hdmi.0/rc/rc0/input3
[ 16.014000] rc rc0: RC for hdmi_cec as /devices/platform/hdmi.0/rc/rc0
[ 16.259000] SGI XFS with security attributes, realtime, no debug enabled
[ 16.583000] r8712u: module is from the staging directory, the quality is unknown, you have been warned.
[ 16.585000] r8712u: register rtl8712_netdev_ops to netdev_ops
[ 16.585000] usb 3-1.3: r8712u: USB_SPEED_HIGH with 4 endpoints
[ 16.586000] usb 3-1.3: r8712u: Boot from EFUSE: Autoload OK
[ 17.308000] usb 3-1.3: r8712u: CustomerID = 0x000a
[ 17.308000] usb 3-1.3: r8712u: MAC Address from efuse = 00:87:23:82:a1:16
[ 17.308000] usb 3-1.3: r8712u: Loading firmware from "rtlwifi/rtl8712u.bin"
[ 17.308000] usbcore: registered new interface driver r8712u
Hi Everyone, I had just done a upgrading and it is now able to read my 5Tb Hdd. But the capacity of the Hdd is wrong, it is reading it as 2.86Tb which my internal Hdd is also showing the same capacity, 2.86Tb.
Well, they should do. Both will pop-up a browser for you to select which file to upload.
Which shows no sign of being recognized.I can only append below the content of dmesg by inserting a flashdrive.
However, you now say that after an upgrade you can see it - so we can ignore this test.
MiracleBox Prem Twin HD - 2@DVB-T2 + Xtrend et8000 - 5(incl. 2 different USBs)@DVB-T2[terrestrial - UK Freeview HD, Sandy Heath] - LAN/USB-stick/HDD
bumperbee (23-05-17)
MiracleBox Prem Twin HD - 2@DVB-T2 + Xtrend et8000 - 5(incl. 2 different USBs)@DVB-T2[terrestrial - UK Freeview HD, Sandy Heath] - LAN/USB-stick/HDD
bumperbee (23-05-17)
Hi Birdman, it did pop-up a browser for me to select files (both methods) and able to select the files too. But after this I need to select upload and a red mark will show besides the file name informing it’s unsuccessful in uploading.
I think not, because I can see the different models of both the Hdd, the only problem is the capacity of the 5Tb is incorrect as it read as 2.86Tb. I am afraid the system will work with the 5Tb Hdd only at 2.86Tb capacity. Append below is the dmesg file.
[ 0.055000] NFS: Registering the id_resolver key type
[ 0.055000] Key type id_resolver registered
[ 0.055000] Key type id_legacy registered
[ 0.055000] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.055000] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 0.056000] fuse init (API version 7.26)
[ 0.061000] bounce: pool size: 64 pages
[ 0.061000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.061000] io scheduler noop registered
[ 0.061000] io scheduler cfq registered (default)
[ 0.061000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.062000] serial8250.0: ttyS0 at MMIO 0x10406b00 (irq = 62, base_baud = 5062500) is a 16550A
[ 0.063000] serial8250.0: ttyS1 at MMIO 0x10406b40 (irq = 63, base_baud = 5062500) is a 16550A
[ 0.063000] serial8250.0: ttyS2 at MMIO 0x10406b80 (irq = 64, base_baud = 5062500) is a 16550A
[ 0.070000] loop: module loaded
[ 0.070000] ahci ahci.0: SSS flag set, parallel bus scan disabled
[ 0.080000] ahci ahci.0: AHCI 0001.0300 32 slots 2 ports 6 Gbps 0x3 impl platform mode
[ 0.080000] ahci ahci.0: flags: ncq sntf stag clo slum part
[ 0.084000] scsi host0: ahci
[ 0.085000] scsi host1: ahci
[ 0.085000] ata1: FORCE: PHY spd limit set to 3.0Gbps
[ 0.085000] ata1: SATA max UDMA/133 mmio [mem 0x10181000-0x10190fff] port 0x100 irq 42
[ 0.085000] ata2: FORCE: PHY spd limit set to 3.0Gbps
[ 0.085000] ata2: SATA max UDMA/133 mmio [mem 0x10181000-0x10190fff] port 0x180 irq 42
[ 0.085000] brcmstb_nand: NAND controller driver is loaded
[ 0.086000] libphy: Fixed MDIO Bus: probed
[ 0.086000] __clk_enable: network [1]
[ 0.086000] bcm7425_pm_network_enable 00
[ 0.086000] __clk_enable: enet [1]
[ 0.086000] bcm40nm_pm_genet_enable 00
[ 0.198000] bcmgenet: configuring instance #0 for internal PHY
[ 0.220000] bcmgenet bcmgenet.0 eth0: link down
[ 0.220000] __clk_disable: enet [0]
[ 0.220000] bcm40nm_pm_genet_disable 00
[ 0.220000] __clk_disable: network [0]
[ 0.220000] bcm7425_pm_network_disable 00
[ 0.220000] __clk_enable: network [1]
[ 0.220000] bcm7425_pm_network_enable 00
[ 0.220000] __clk_enable: moca_genet [1]
[ 0.220000] bcm40nm_pm_genet1_enable 00
[ 0.220000] __clk_enable: moca [1]
[ 0.220000] bcm40nm_pm_moca_enable 00
[ 0.233000] Found PHY at Address 31
[ 0.233000] bcmgenet: configuring instance #1 for external RGMII
[ 0.233000] __clk_disable: moca [0]
[ 0.233000] bcm40nm_pm_moca_disable 00
[ 0.233000] __clk_disable: moca_genet [0]
[ 0.233000] bcm40nm_pm_genet1_disable 00
[ 0.233000] __clk_disable: network [0]
[ 0.233000] bcm7425_pm_network_disable 00
[ 0.233000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.233000] __clk_enable: usb [1]
[ 0.233000] bcm40nm_pm_usb_enable 00
[ 0.233000] ehci-brcm ehci-brcm.0: Broadcom STB EHCI
[ 0.233000] ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1
[ 0.243000] ehci-brcm ehci-brcm.0: irq 66, io mem 0x10480300
[ 0.250000] ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
[ 0.250000] hub 1-0:1.0: USB hub found
[ 0.250000] hub 1-0:1.0: 1 port detected
[ 0.250000] ehci-brcm ehci-brcm.1: Broadcom STB EHCI
[ 0.250000] ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus number 2
[ 0.261000] ehci-brcm ehci-brcm.1: irq 67, io mem 0x10480500
[ 0.268000] ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00
[ 0.268000] hub 2-0:1.0: USB hub found
[ 0.268000] hub 2-0:1.0: 1 port detected
[ 0.268000] ehci-brcm ehci-brcm.2: Broadcom STB EHCI
[ 0.268000] ehci-brcm ehci-brcm.2: new USB bus registered, assigned bus number 3
[ 0.279000] ehci-brcm ehci-brcm.2: irq 71, io mem 0x10490300
[ 0.286000] ehci-brcm ehci-brcm.2: USB 0.0 started, EHCI 1.00
[ 0.286000] hub 3-0:1.0: USB hub found
[ 0.286000] hub 3-0:1.0: 1 port detected
[ 0.286000] ehci-brcm ehci-brcm.3: Broadcom STB EHCI
[ 0.286000] ehci-brcm ehci-brcm.3: new USB bus registered, assigned bus number 4
[ 0.297000] ehci-brcm ehci-brcm.3: irq 72, io mem 0x10490500
[ 0.304000] ehci-brcm ehci-brcm.3: USB 0.0 started, EHCI 1.00
[ 0.304000] hub 4-0:1.0: USB hub found
[ 0.304000] hub 4-0:1.0: 1 port detected
[ 0.304000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.304000] ohci-brcm ohci-brcm.0: Broadcom STB OHCI
[ 0.305000] ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 5
[ 0.305000] ohci-brcm ohci-brcm.0: irq 68, io mem 0x10480400
[ 0.371000] hub 5-0:1.0: USB hub found
[ 0.371000] hub 5-0:1.0: 1 port detected
[ 0.371000] ohci-brcm ohci-brcm.1: Broadcom STB OHCI
[ 0.371000] ohci-brcm ohci-brcm.1: new USB bus registered, assigned bus number 6
[ 0.372000] ohci-brcm ohci-brcm.1: irq 69, io mem 0x10480600
[ 0.397000] ata1: SATA link down (SStatus 0 SControl 320)
[ 0.407000] ata1: exception Emask 0x10 SAct 0x0 SErr 0x4000000 action 0xe frozen
[ 0.407000] ata1: irq_stat 0x00000040, connection status changed
[ 0.407000] ata1: SError: { DevExch }
[ 0.407000] ata1: hard resetting link
[ 0.438000] hub 6-0:1.0: USB hub found
[ 0.438000] hub 6-0:1.0: 1 port detected
[ 0.438000] ohci-brcm ohci-brcm.2: Broadcom STB OHCI
[ 0.438000] ohci-brcm ohci-brcm.2: new USB bus registered, assigned bus number 7
[ 0.439000] ohci-brcm ohci-brcm.2: irq 73, io mem 0x10490400
[ 0.505000] hub 7-0:1.0: USB hub found
[ 0.505000] hub 7-0:1.0: 1 port detected
[ 0.505000] ohci-brcm ohci-brcm.3: Broadcom STB OHCI
[ 0.505000] ohci-brcm ohci-brcm.3: new USB bus registered, assigned bus number 8
[ 0.506000] ohci-brcm ohci-brcm.3: irq 74, io mem 0x10490600
[ 0.572000] hub 8-0:1.0: USB hub found
[ 0.572000] hub 8-0:1.0: 1 port detected
[ 0.573000] usbcore: registered new interface driver uas
[ 0.573000] usbcore: registered new interface driver usb-storage
[ 0.573000] mousedev: PS/2 mouse device common for all mice
[ 0.573000] i2c /dev entries driver
[ 0.573000] usbcore: registered new interface driver btusb
[ 0.573000] hidraw: raw HID events driver (C) Jiri Kosina
[ 0.573000] usbcore: registered new interface driver usbhid
[ 0.573000] usbhid: USB HID core driver
[ 0.574000] NET: Registered protocol family 17
[ 0.574000] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 0.574000] Bluetooth: HIDP socket layer initialized
[ 0.574000] Key type dns_resolver registered
[ 0.574000] PM: CP0 COUNT/COMPARE frequency does not depend on divisor
[ 0.575000] EBI CS1: setting up NAND flash (primary)
[ 0.575000] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xd3
[ 0.575000] nand: Samsung NAND 1GiB 3,3V 8-bit
[ 0.575000] nand: 1024 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 0.575000] brcmnand brcmnand.0: 1024MiB total, 128KiB blocks, 2KiB pages, 16B OOB, 8-bit, BCH-16 (1KiB sector)
[ 0.576000] Bad block table found at page 524224, version 0x01
[ 0.576000] Bad block table found at page 524160, version 0x01
[ 0.577000] nand_read_bbt: bad block at 0x00002f080000
[ 0.577000] nand_read_bbt: bad block at 0x000032740000
[ 0.577000] Creating 3 MTD partitions on "brcmnand.0":
[ 0.577000] 0x000000000000-0x000040000000 : "complete"
[ 0.583000] 0x000000000000-0x000000600000 : "kernel"
[ 0.584000] 0x000000600000-0x000040000000 : "rootfs"
[ 0.590000] EBI CS0: setting up SPI flash
[ 0.590000] brcm_setup_spi_flash: can't locate SPI master
[ 0.590000] brcm_setup_cs: can't register SPI flash (error -19)
[ 0.591000] ubi0: default fastmap pool size: 256
[ 0.591000] ubi0: default fastmap WL pool size: 128
[ 0.591000] ubi0: attaching mtd2
[ 0.600000] usb 3-1: new high-speed USB device number 2 using ehci-brcm
[ 0.702000] ata2: SATA link down (SStatus 0 SControl 320)
[ 0.719000] hub 3-1:1.0: USB hub found
[ 0.719000] hub 3-1:1.0: 4 ports detected
[ 0.920000] ubi0: attached by fastmap
[ 0.920000] ubi0: fastmap pool size: 256
[ 0.920000] ubi0: fastmap WL pool size: 128
[ 0.936000] ubi0: attached mtd2 (name "rootfs", size 1018 MiB)
[ 0.936000] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 0.936000] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 0.936000] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 0.936000] ubi0: good PEBs: 8138, bad PEBs: 6, corrupted PEBs: 0
[ 0.936000] ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 0.936000] ubi0: max/mean erase counter: 3/1, WL threshold: 4096, image sequence number: 2074121938
[ 0.936000] ubi0: available PEBs: 0, total reserved PEBs: 8138, PEBs reserved for bad PEB handling: 154
[ 0.936000] ubi0: background thread "ubi_bgt0d" started, PID 82
[ 0.936000] ALSA device list:
[ 0.936000] No soundcards found.
[ 0.936000] Warning: unable to open an initial console.
[ 0.938000] UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 83
[ 1.004000] usb 3-1.1: new full-speed USB device number 3 using ehci-brcm
[ 1.048000] UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[ 1.048000] UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 1.048000] UBIFS (ubi0:0): FS size: 1011617792 bytes (964 MiB, 7967 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[ 1.048000] UBIFS (ubi0:0): reserved for root: 0 bytes (0 KiB)
[ 1.048000] UBIFS (ubi0:0): media format: w4/r0 (latest is w5/r0), UUID 570219F0-4287-4767-BDC6-42567E1E8A09, small LPT model
[ 1.054000] VFS: Mounted root (ubifs filesystem) on device 0:12.
[ 1.056000] devtmpfs: mounted
[ 1.056000] Freeing unused kernel memory: 276K
[ 1.056000] This architecture does not have kernel memory protection.
[ 1.130000] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
[ 1.131000] ata1.00: ATA-9: WDC WD3003FZEX-00Z4SA0, 01.01A01, max UDMA/133
[ 1.131000] ata1.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 1.131000] ata1.00: configured for UDMA/133
[ 1.131000] ata1: EH complete
[ 1.132000] scsi 0:0:0:0: Direct-Access ATA WDC WD3003FZEX-0 1A01 PQ: 0 ANSI: 5
[ 1.140000] sd 0:0:0:0: [sda] 5860533168 512-byte logical blocks: (3.00 TB/2.73 TiB)
[ 1.140000] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 1.140000] sd 0:0:0:0: [sda] Write Protect is off
[ 1.141000] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.141000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.141000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.177000] usb 3-1.3: new high-speed USB device number 4 using ehci-brcm
[ 1.181000] sda: sda1
[ 1.182000] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.286000] random: crng init done
[ 2.359000] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 8.093000] tpm: loading out-of-tree module taints kernel.
[ 8.094000] usbcore: registered new interface driver tpm
[ 11.402000] dvb: module_layout: kernel tainted.
[ 11.402000] Disabling lock debugging due to kernel taint
[ 15.001000] input: dreambox remote control (native) as /devices/virtual/input/input0
[ 15.002000] input: dreambox advanced remote control (native) as /devices/virtual/input/input1
[ 15.038000] dvbdev: DVB: registering new adapter (dvb0)
[ 15.039000] platform dvb0.0: DVB: registering adapter 0 frontend 0 (DVB-C)...
[ 15.040000] platform dvb0.0: DVB: registering adapter 0 frontend 1 (DVB-C)...
[ 15.041000] platform dvb0.0: DVB: registering adapter 0 frontend 2 (DVB-C)...
[ 15.042000] platform dvb0.0: DVB: registering adapter 0 frontend 3 (DVB-C)...
[ 15.376000] input: front panel as /devices/virtual/input/input2
[ 16.187000] Registered IR keymap rc-cec
[ 16.187000] input: RC for hdmi_cec as /devices/platform/hdmi.0/rc/rc0/input3
[ 16.188000] rc rc0: RC for hdmi_cec as /devices/platform/hdmi.0/rc/rc0
[ 16.446000] SGI XFS with security attributes, realtime, no debug enabled
[ 16.778000] r8712u: module is from the staging directory, the quality is unknown, you have been warned.
[ 16.780000] r8712u: register rtl8712_netdev_ops to netdev_ops
[ 16.780000] usb 3-1.3: r8712u: USB_SPEED_HIGH with 4 endpoints
[ 16.781000] usb 3-1.3: r8712u: Boot from EFUSE: Autoload OK
[ 17.502000] usb 3-1.3: r8712u: CustomerID = 0x000a
[ 17.502000] usb 3-1.3: r8712u: MAC Address from efuse = 00:87:23:82:a1:16
[ 17.502000] usb 3-1.3: r8712u: Loading firmware from "rtlwifi/rtl8712u.bin"
[ 17.503000] usbcore: registered new interface driver r8712u
It seems that here is (was) a recent issue here, that is being looked into:
http://www.world-of-satellite.com/sh...hments-(phots)
MiracleBox Prem Twin HD - 2@DVB-T2 + Xtrend et8000 - 5(incl. 2 different USBs)@DVB-T2[terrestrial - UK Freeview HD, Sandy Heath] - LAN/USB-stick/HDD
bumperbee (23-05-17)
In which case I'm confused, as the dmesg report you attached only shows the presence of one disk
Where can you see "the different models of both the Hd"?[ 1.132000] scsi 0:0:0:0: Direct-Access ATA WDC WD3003FZEX-0 1A01 PQ: 0 ANSI: 5
[ 1.140000] sd 0:0:0:0: [sda] 5860533168 512-byte logical blocks: (3.00 TB/2.73 TiB)
[ 1.140000] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 1.140000] sd 0:0:0:0: [sda] Write Protect is off
[ 1.141000] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.141000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.141000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.177000] usb 3-1.3: new high-speed USB device number 4 using ehci-brcm
[ 1.181000] sda: sda1
[ 1.182000] sd 0:0:0:0: [sda] Attached SCSI disk
MiracleBox Prem Twin HD - 2@DVB-T2 + Xtrend et8000 - 5(incl. 2 different USBs)@DVB-T2[terrestrial - UK Freeview HD, Sandy Heath] - LAN/USB-stick/HDD
bumperbee (23-05-17)
It is in Vix>Device Manager
bumperbee (24-05-17)
Can you post the contents or /proc/partitions when you have the 5TB disk plugged in, please?
MiracleBox Prem Twin HD - 2@DVB-T2 + Xtrend et8000 - 5(incl. 2 different USBs)@DVB-T2[terrestrial - UK Freeview HD, Sandy Heath] - LAN/USB-stick/HDD
bumperbee (24-05-17)
very interesting same image number and on solo2 no network mounts,must do a new thread.
bumperbee (24-05-17)