Hi All
Had a scan on the net and couldnt find any resolution.
Is there a way to control the TV (and amp?) using the VU+ Remote
I have VU+ Duo, Panasonic TX-L50G10B and Onkyo TXSR507
Thanks in advance
Hi All
Had a scan on the net and couldnt find any resolution.
Is there a way to control the TV (and amp?) using the VU+ Remote
I have VU+ Duo, Panasonic TX-L50G10B and Onkyo TXSR507
Thanks in advance
My posts contain my own personal thoughts and opinions, they do not represent those of any organisation or group but my own.
If you don't like what I post, Don't read it.
SIMPLES.
hsbajwa316 (10-10-12),ozzy30 (11-04-19)
Hi,
you can see if you have a new or old remote on the top left. When you have a TV button on the top left you have a new RC. The DUO manual is not complete when it comes to program the RC look in the web for the UNO manual.
ciao
---
Sat:VU+ Ultimo4K/Solo4K/Duo2/2*Solo2/Ultimo
Remote: Harmony 200, 700, Link, Smart Control, Smart Companion, Elite, 2*Ultimate, Keyboard
hsbajwa316 (10-10-12)
Hi I have the new remote, how do i go about this
Hi,
download and read the UNO or Ultimo manual there is a chapter about programming the RC.
ciao
---
Sat:VU+ Ultimo4K/Solo4K/Duo2/2*Solo2/Ultimo
Remote: Harmony 200, 700, Link, Smart Control, Smart Companion, Elite, 2*Ultimate, Keyboard
hsbajwa316 (13-10-12)
remote is simple
hold down 1+3
type 0000
then hole the tv power (top left) until tv goes off
when it does let go
now press ok +stop
all done
hsbajwa316 (13-10-12)
Hi the above didnt work, ill try downloading the manual
Hi All, still not working and now when I press the STB power off button its putting the TV on standby and when I turn it back on it keeps putting the wrong HDMI channel on. Is there any way to rest all this and go back to normal I have tried 1+6 , 996 and taking the batteries out but its not changing anything.
1+6 996
that does reset it back to default
hsbajwa316 (21-10-12)
If you did the '1+6 996 trick' the R/C is back to default and not operating the TV.
Did you have a look at the HDMI-CEC plugin? Is it set to disabled?
Help asked via PM will be ignored.
The forum is there for help and all will benefit from your questions.
NO CARD SHARING TALK WILL BE TOLERATED, LAN OR WAN, IN OPEN FORUM OR PM !
English is not my native tongue.
I apologise for all my grammar, spelling and idiom errors.
hsbajwa316 (21-10-12)
You can force the Panasonic to startup on any HDMI input. Google for 'Panasonic Hotel Mode'.
Also, be careful when using the remote setup procedure detailed above. I found that the remote would find a code which could power my panasonic TV on and off, but would not operate the volume. To get around this, after entering 0000 on the remote, I would keep either the volume up or volume down button pressed until the TV volume started working. The remainder of the setup procedure was the same.
hsbajwa316 (21-10-12)
Hi All thanks for all your help didnt manage to get it working so have just disabled it, thanks for tip around the hotel mode works like a charm
hold down 1+3
type 0000
then hole the tv power (top left) until tv goes off
when it does let go
now press ok +stop
all done
this does work but can take a long time just done it on my solo 4k took about 10 minutes
Last edited by conwaysly1961; 11-05-17 at 12:05.