Hello Guest, if you are reading this it means you have not registered yet. Please take a second, Click here to register, and in a few simple steps you will be able to enjoy our community and use our OpenViX support section.
Results 1 to 4 of 4

Thread: Unable to see 2nd sat tuner

  1. #1

    Title
    Member
    Join Date
    Dec 2015
    Posts
    79
    Thanks
    0
    Thanked 6 Times in 6 Posts

    Unable to see 2nd sat tuner

    Hi

    I have recently purchased a sat tuner from the sponsors for my ET10000 as I wanted to replace my cable tuner. I currently have a cable tuner in slot A (which I am currently not using) and my new sat tuner is slot B. I have screwed both my sat feeds into the sat tuner and it does find the tuner when I try and configure it, however, it does not show the 2nd tuner. I thought that it might be my cables that were the problem so I swapped them round but it is still the same. I then just had one cable screwed in to see what would happen. When the cable is in the top tuner, i get a picture. When I screw it into the bottom tuner, I get a message to say either "tune failed" or when I try a scan "Timeout for tuner lock". Is there something I am missing in my setup?

    I have attached some pictures if this helps to show my issue:

    1 - Shows that the tuner shows up in slot B, labelled Tuner B (I thought that it should show tuner B & C for both sat tuners)
    2 - Current set up of tuner B
    3 - Shows both feeds in the sat tuner
    4 - Shows the feed in bottom tuner. When I have tried it, I get the "timeout for tuner lock" or "tune failed" messages
    5 - shows one of the errors
    6 - shows the other error.

    I want to have it set up for I can watch one channel and record another.

    Any help would be appreciated.

    Thanks
    Attached Images Attached Images

  2. #2
    Huevos's Avatar
    Title
    Administrator
    Join Date
    Jun 2010
    Location
    38.5N, 0.5W
    Posts
    13,945
    Thanks
    2,062
    Thanked 5,145 Times in 3,395 Posts
    What do you mean both sat tuners? Tuner in slot 2 is a single. Second socket is for loop out to another device. Cable from the dish must be attached to RF input socket.
    Help keep OpenViX servers online.Please donate!

  3. #3

    Title
    Member
    Join Date
    Dec 2015
    Posts
    79
    Thanks
    0
    Thanked 6 Times in 6 Posts
    That will explain it then. I thought that as it had two connections, I could put both feeds into it. Do you know if they make a duel tuner for sat as there was not one for sale? Thanks

  4. #4

    Title
    Moderator
    Join Date
    Jul 2010
    Posts
    4,684
    Thanks
    1,205
    Thanked 2,524 Times in 1,349 Posts
    I don't think they do for xtrend, you'd have to buy another single tuner.
    Vu Ultimo4K, OpenViX 5.0, 8xdvb-c, 8xdvb-s2, 2xdvb-t2
    Vu Solo4K, OpenViX 5.0, 8xdvb-s2
    Dreambox DM900, OpenViX 5.0, 2xdvb-s2, 2xdvb-c/t2
    Terrestrial, Cable, Fixed 28.2e + Unicable2 LNB

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
This website uses cookies
We use cookies to store session information to facilitate remembering your login information, to allow you to save website preferences, to personalise content and ads, to provide social media features and to analyse our traffic. We also share information about your use of our site with our social media, advertising and analytics partners.