In the AV settings on the solo2 what is the output set as? I used the yellow rca socket without problem.
In the AV settings on the solo2 what is the output set as? I used the yellow rca socket without problem.
Zgemma H7S running OpenVIX 6.2, Darkmotor, Triax TD110 dish, Inverto Black Ultra dual lnb
LG 50UM7450 4K TV, Pioneer VSX-534 Atmos AVR , Panasonic UB820 region free 4K Bluray & a PS4.
Also you are using AV1 for both scart and composite on your TV? On my TVs (and any others I have seen) these are separate inputs.
Zgemma H7S running OpenVIX 6.2, Darkmotor, Triax TD110 dish, Inverto Black Ultra dual lnb
LG 50UM7450 4K TV, Pioneer VSX-534 Atmos AVR , Panasonic UB820 region free 4K Bluray & a PS4.
I can only repeat that using one single yellow cinch connection between my Solo2 and my Sony TV switching between 3:4 & 16:9 works as expected. I didn't even setup anything analogue output related: my A/V-settings remained untouched on HDMI/1080p/multi.
Help asked via PM will be ignored.
The forum is there for help and all will benefit from your questions.
NO CARD SHARING TALK WILL BE TOLERATED, LAN OR WAN, IN OPEN FORUM OR PM !
English is not my native tongue.
I apologise for all my grammar, spelling and idiom errors.
ronand (19-05-16)
As per @ronand's reply - AV1, AV2 and AV3 are physically separate connections on my TV also. AV1 is SCART, AV2 is S-Video and AV3 is the composite. You should use connection-specific settings on the TV rather than the same for everything. On my HDMI input I use "exact pixel" so there is no overscan. On AV3 I use "wide" as the default and the picture switches between widescreen and 4:3 as the broadcaster changes aspect ratio. I think the ViX info screen for the broadcast channel will always show 16:9 as the screen ratio as this is derived from the satellite/cable/terrestrial meta data transmitted. It is the actual video stream content data that will switch from 16:9 to 4:3 as necessary.
Try setting your AV2 (or whatever) to "full wide" and flick from channel to channel - usually CBS Action or one of the low-budget channels will be showing 4:3 material through the day. (or Channel 4 from 08:00 - 10:30)
GB Quad Plus, Mut@nt HD51, AX HD61, 80cm dish and Supreme Dark motor. Sony TA-AN1000, Sony UBP-X800M2 Bluray, Odroid N2+ (CoreElec), Monitor Audio Bronze 5.1 speakers
It doesn't take long to set up a fresh image using ABM (autobouquetmaker) to set up your channels.
Zgemma H7S running OpenVIX 6.2, Darkmotor, Triax TD110 dish, Inverto Black Ultra dual lnb
LG 50UM7450 4K TV, Pioneer VSX-534 Atmos AVR , Panasonic UB820 region free 4K Bluray & a PS4.
Test 1 in #28 shows that the Solo2 SCART is working as expected.
Test 2 shows that when you put that same (working) signal through your RCA cable it stops working at the TV end.
So it's not the Solo2 failing.
Do you have another RCA cable?
MiracleBox Prem Twin HD - 2@DVB-T2 + Xtrend et8000 - 5(incl. 2 different USBs)@DVB-T2[terrestrial - UK Freeview HD, Sandy Heath] - LAN/USB-stick/HDD
Well, in test #1 it can be the WSS-signal on the dedicated scart-pin, which is not being used when using only the yellow cable.
Anyway: IMHO a TV issue, as it works perfect here.
Help asked via PM will be ignored.
The forum is there for help and all will benefit from your questions.
NO CARD SHARING TALK WILL BE TOLERATED, LAN OR WAN, IN OPEN FORUM OR PM !
English is not my native tongue.
I apologise for all my grammar, spelling and idiom errors.
I can't. But I can't reproduce the problem here either.
Help asked via PM will be ignored.
The forum is there for help and all will benefit from your questions.
NO CARD SHARING TALK WILL BE TOLERATED, LAN OR WAN, IN OPEN FORUM OR PM !
English is not my native tongue.
I apologise for all my grammar, spelling and idiom errors.
abu baniaz (21-05-16)
OK Guys,
I have figured it out and it was the TV setting "ORIGINAL"
http://www.world-of-satellite.com/at...7&d=1463646306
that was causing the problem with the Solo2 - However, I have it on ORIGINAL for the Sky+HD box and that switches between 4:3 and 16:9 mode in ORIGINAL. Me changing it to 16:9 on each TV around the house sorted the issue.
I always thought that "ORIGINAL" (instead of hard setting it to 16:9) would select the screen size based on the output of the video cable - and with the Solo2 box supporting Line 23 WSS flags that the "Original" signal would be either 4:3 or 16:9 and the TV could switch as necessary (exactly as the Sky+HD box seemingly does)
The only thing I can think of is that the Sky+HD box has a setting (Settings / Picture) called "SCART / RF1 Picture Format" which is set to 16:9. Maybe that makes the TV's see the ORIGINAL output as 16:9 and me setting the TVs to 16:9 means the Solo2 box doesn't have to do that?
Anyway, It's sorted now, there isn't an issue / fault with the Solo2 - it just outputs differently via SCART / Composite compared to the Sky+HD box.
Thank you to everyone who spared their time to be involved in this thread and for your ideas and suggestions.
abu baniaz (21-05-16),Joe_90 (21-05-16),twol (21-05-16)
I suggested you change your TV setting from "original" to "full wide" (as per my Sony) back in post #35. Different settings for different inputs and all that.... In any case you have finally cracked it
GB Quad Plus, Mut@nt HD51, AX HD61, 80cm dish and Supreme Dark motor. Sony TA-AN1000, Sony UBP-X800M2 Bluray, Odroid N2+ (CoreElec), Monitor Audio Bronze 5.1 speakers
Timbo (23-05-16)
indeed you did, but I have never needed to do that before, even with the duo that the solo2 replaced. Which is why I was convinced that wasn't the issue.
you live and learn I guess.
Next question: Is there any way of getting a 1280 x 720 image to display full screen on a 576i display via a Solo2 box? zoom out plugin or something? I have an IP camera and the output is getting cropped via non-HD methods. Displays fine via HDMI on screens that support "just scan" / "overscan off"