just got a venton unibox hd eco and when i scan 28.2 i only get about 350 channels any ideas ppl
just got a venton unibox hd eco and when i scan 28.2 i only get about 350 channels any ideas ppl
Are you using ABM? (Menu>Setup>Service Searching>ABM)
Sent from my iPhone using Tapatalk
Vu+ Ultimo 4K with 3TB HDD, Dual FBC (Sat) tuners, 1x Twin Hybrid DVB-C/T/T2 tuner
Vu+ Solo 4K with 1TB HDD, Dual FBC (Sat) tuners, 1x Hybrid DVB-C/T/T2 tuner
Vu+ Solo 2 with 1TB HDD 'White Edition', 2x DVB-S2 tuners
Mut@nt HD2400 with 1TB HDD, 4x DVB-S2 tuners
Fixed 28.2E Technomate 65cm Mesh Satellite Dish with Inverto Unicable II/JESS LNB and Inverto Unicable Splitter
Fixed 28.2E Sky Zone 1 45cm Satellite Dish with Octo LNB
(All receivers installed with the latest Dev build)
this is when i do a fresh scan no autobuoquets only 400 channels found should be about 930
Possible reasons are:
F-plug issue, i.e not connected properly
LNB faulty. (Some LNBs mis behave when two receivers are connected to them)
Dish misaligned
Damaged cable
Tuner faulty
cables are fine mate box has its own dish with 99% signal quality and strength, i think it must be down to the tuner, the box is brand new out the box today
Try ABM please. Use expert mode, also make sure "not indexed channels" is set to yes, and in providers use "custom region", then start scan.
Sent from my iPhone using Tapatalk
Vu+ Ultimo 4K with 3TB HDD, Dual FBC (Sat) tuners, 1x Twin Hybrid DVB-C/T/T2 tuner
Vu+ Solo 4K with 1TB HDD, Dual FBC (Sat) tuners, 1x Hybrid DVB-C/T/T2 tuner
Vu+ Solo 2 with 1TB HDD 'White Edition', 2x DVB-S2 tuners
Mut@nt HD2400 with 1TB HDD, 4x DVB-S2 tuners
Fixed 28.2E Technomate 65cm Mesh Satellite Dish with Inverto Unicable II/JESS LNB and Inverto Unicable Splitter
Fixed 28.2E Sky Zone 1 45cm Satellite Dish with Octo LNB
(All receivers installed with the latest Dev build)
Where you purchased is dumping old discontinued stock. Driver issue or faulty tuner. Also no longer supported by openvix.
Sent from my iPhone using Tapatalk
D I S C L A I M E R
My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!
Please help keep OpenViX online, donate HERE.
Rules can be found HERE
Support our sponsor World-Of-Satellite HERE
GIGABLUE UHD QUAD 4K, VU+ DUO 4K SE, ZGEMMA H7S, VU+ UNO 4K SE
Triax 1.1m Powered by TM2600, Fixed 28.2 Zone 2 dish with GT-SAT Unicable
got openvix new image on it would it be worth trying other images ?
There is no openvix 4.0 for this box, support was stopped at 3.2.037. See www.openvix.co.uk
See here http://www.openvix.co.uk/index.php/d...x-hd-eco-plus/
Sent from my iPhone using Tapatalk
D I S C L A I M E R
My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!
Please help keep OpenViX online, donate HERE.
Rules can be found HERE
Support our sponsor World-Of-Satellite HERE
GIGABLUE UHD QUAD 4K, VU+ DUO 4K SE, ZGEMMA H7S, VU+ UNO 4K SE
Triax 1.1m Powered by TM2600, Fixed 28.2 Zone 2 dish with GT-SAT Unicable
Having exactly the same problem, same box same image. Only about 350 channels are found when scanned. Tied manual scan, abs scan and auto bouquets scan.
Tested three other boxes on the same feed an they are all fine.
Dodgy sat tuner without a doubt!
i put a agonis image on from the downloads and that image works finds all channels.